User manual MTD 92908

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MTD 92908. We hope that this MTD 92908 user guide will be useful to you.


MTD 92908 : Download the complete user guide (820 Ko)

Manual abstract: user guide MTD 92908

Detailed instructions for use are in the User's Guide.

[. . . ] Operating & Maintenance Instructions Model Series Covered in This Manual 90000 100000 Model Type Code Note: General Model Series numbers noted above are inclusive of the specific model number found on your engine. To get replacement parts or technical assistance in the future, write your engine Model, Type, Code and date of purchase here. WARNING Briggs & Stratton does not approve or authorize the use of these engines on 3-wheel All Terrain Vehicles (ATVs), motor bikes, aircraft products or vehicles intended for use in competitive events. Use of these engines in such applications could result in property damage, serious injury (including paralysis), or even death. [. . . ] € Carefully remove air cleaner to prevent debris from falling into carburetor. Saturate Oil-Foam element in engine oil and squeeze in a clean cloth to remove excess oil. Note: On Style 2 air cleaner, install element so lip Ê extends over edge of body to form protective seal when cover is assembled. 0000 ÌÌÌÌ ÌÌÌÌÌ ÌÌÌÌ ÌÌÌÌÌ ÌÌÌÌÌ ÌÌÌÌÌ ÌÌÌÌÌ ÌÌÌÌÌ ÌÌÌÌÌÌ ÌÌÌ ÌÌÌÌÌÌ ÌÌÌ ÌÌÌÌÌÌ ÌÌÌÌÌÌ ÌÌÌÌÌÌ ÌÌÌÌÌÌ Ê 12 TAB SCREWS REMOVE BLOWER HOUSING Cover / blower housing KEEP AREAS WITHIN HEAVY LINE CLEAR OF ALL DEBRIS SCREW DO NOT BEND OR REMOVE Air Cooling System REMOVING AND RE-INSTALLING BLOWER HOUSING [1] [2] COVER/ Remove 2 screws from cover (if equipped) and lift cover straight until tab clears. MAINTENANCE ENGINE AND ENGINE PARTS We recommend that you see an authorized Briggs & Stratton Service Dealer for all maintenance and service of the engine and engine parts. If you perform any maintenance on the engine, first disconnect the spark plug wire from the spark plug, and disconnect the battery at the negative terminal (electric WARNING starter engines only) to prevent unintentional sparking. WARNING MUFFLER • Do not strike the flywheel with a hammer or hard object because the flywheel may later shatter during operation. € Do not tamper with governor spring, links or other parts to increase engine speed. CLEANING DEBRIS Replacement parts for the muffler must be the same and installed in the same position as the original parts, otherwise fire can occur. WARNING If muffler is equipped with spark arrester screen, remove screen for inspection. WARNING Engine parts should be kept clean to reduce the risk of overheating and ignition of accumulated debris. SPARK PLUG Use only Briggs & Stratton Spark Tester (part number 19368) to check for spark. Note: In some areas, local law requires using resistor spark plug to suppress ignition signals. If this engine was originally equipped with resistor spark plug, use same type for replacement. 76 mm) WIRE GAGE FINGER GUARD Daily or before every use, clean grass, chaff or accumulated debris from engine. ROTATING SCREEN CLEAN COMBUSTION DEPOSITS We recommend that after every 100-300 hours you have an authorized Briggs & Stratton Service Dealer remove combustion deposits from the cylinder, cylinder head, top of piston, and around valves. finger Guard Linkage , Springs & Controls FUEL SYSTEM CLEAN WARNING Replacement parts for fuel system (cap , hoses , tanks , filters , etc. 0000 ADJUSTMENTS CARBURETOR ADJUSTMENT The carburetor on this engine is not adjustable. WARNING WARNING The manufacturer of the equipment on which this engine is installed specifies top speed at which the engine will be operated. Before performing adjustments, remove spark plug wire from spark plug. THROTTLE ADJUSTMENT If the engine does not start or if it runs roughly, the remote throttle control may need adjustment. See your authorized Briggs & Stratton dealer or follow the instructions below. [. . . ] Also included may be connectors and other emission related assemblies. Where a warrantable condition exists, B&S will repair your small off-road engine at no cost to you including diagnosis, parts and labor. Briggs & Stratton Emission Control Defects Warranty Coverage Small off-road engines are warranted relative to emission control parts defects for a period of two years, subject to provisions set forth below. If any covered part on your engine is defective, the part will be repaired or replaced by B&S. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MTD 92908




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MTD 92908 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.