Detailed instructions for use are in the User's Guide.
[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
U Series CE Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST380020ACE, ST360020ACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST340810ACE, ST320410ACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ultra ATA Interface Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Seagate Technology, LLC has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disc drive, motherboard, power supply, etc. ) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception. This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television, which can be determined by turning the equipment on and off, you are encouraged to try one or more of the following corrective measures:
· · · ·
Reorient the receiving antenna. Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.
If necessary, you should consult your dealer or an experienced radio/ television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission: How to Identify and Resolve Radio-Television Interference Problems. Refer to publication number 004-000-00345-4.
U Series CE Family Product Manual, Rev. A
17
2. 0 Configuring and mounting the drive
This section contains the specifications and instructions for configuring and mounting the drive.
2. 1 Handling and static-discharge precautions
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions: Caution:
· The SeaShellTM replaces electrostatic discharge (ESD) bags. The
SeaShell package is a shock-ribbed, transparent clamshell enclosure that limits a drive's exposure to ESD and also protects against external shocks and stresses. The design permits attaching cables, software loading and label/barcode scanning without removing the drive from the SeaShell. Keep the drive in the SeaShell package until you are ready for installation.
· The drive is enclosed in a black, flexible cover called a SeaShield. Do
not remove this permanent cover--it protects the drive from electrostatic discharge (ESD) and minor impact damage. The soft SeaShield cover also includes installation instructions and jumper settings. Removing the SeaShield voids the warranty.
· Before handling the drive, put on a grounded wrist strap, or ground
yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.
· Handle the drive by its edges or frame only. Do not press down
on the drive top cover.
· Always rest the drive on a padded, antistatic surface until you mount
it in the computer.
· Do not touch the connector pins or the printed circuit board. · Do not remove the factory-installed labels from the drive or cover them
with additional labels. Some factoryinstalled labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.
18
U Series CE Family Product Manual, Rev. [. . . ] The following commands contain drive-specific features that may not be included in the Draft ATA-Rev 6 Standard.
U Series CE Family Product Manual, Rev. A Word 0 Description Configuration information: · Bit 15: 0 = ATA; 1 = ATAPI · Bit 7: removable media · Bit 6: removable controller · Bit 0: reserved Number of logical cylinders ATA-reserved Number of logical heads Retired Retired Number of logical sectors per logical track: 63 Retired Serial number: (20 ASCII characters, 0000H = none) Retired Retired Obsolete Firmware revision (8 ASCII character string, padded with blanks to end of string) Drive model number: (40 ASCII characters, padded with blanks to end of string) Maximum sectors per interrupt on Read multiple and Write multiple (32) Reserved Standard Standby timer, IORDY supported and may be disabled Value
25
0C5AH
1 2 3 4 5 6 79 1019 20 21 22 2326
16, 383
0000H
16
0000H 0000H 003FH 0000H ASCII 0000H 0400H 0004H
x. xx
ST380020ACE ST360020ACE ST340810ACE ST320410ACE
2746
47
8020H 0000H 2F00H
48 49
26 Word 50 51 52 53 54 55 56 5758 59
U Series CE Family Product Manual, Rev. A Description Device-specific standby timer value PIO data-transfer cycle timing mode Retired Words 5458, 6470 and 88 are valid Number of current logical cylinders Number of current logical heads Number of current logical sectors per logical track Current capacity in sectors Number of sectors transferred during a Read Multiple or Write Multiple command Total number of user-addressable LBA sectors available (see Section 2. 2. 3 for related information) 62 63 Retired Multiword DMA active and modes supported (see note following this table) Advanced PIO modes supported (modes 3 and 4 supported) Minimum multiword DMA transfer cycle time per word (120 nsec) Value 0000H
0200H 0200H 0007H
xxxxH xxxxH
xxxxH xxxxH xxxxH
ST380020ACE = 160, 045, 200 ST360020ACE = 120, 033, 900 ST340810ACE = 80, 022, 600 ST320410ACE = 40, 011, 300
6061
0000H
xx07H
64
0003H
65
0078H
U Series CE Family Product Manual, Rev. A Word 66 Description Recommended multiword DMA transfer cycle time per word (120 nsec) Minimum PIO cycle time without IORDY flow control (240 nsec) Minimum PIO cycle time with IORDY flow control (120 nsec) ATA-reserved Queue depth ATA-reserved Major version number Minor version number Command sets supported Command sets supported Command sets support extension Command sets enabled Command sets enabled Command sets enable extension Ultra DMA support and current mode (see note following this table) Security erase time Enhanced security erase time Advanced Power Management value Value 0078H
27
67
00F0H
68
0078H 0000H 0000H 0000H 007EH 0000H 346BH 4B09H 4003H
6974 75 7679 80 81 82 83 84 85 86 87 88
xxxxH xxxxH xxxxH xx3FH
89 90 91
0000H 0000H 0040H
28 Word 92 93
U Series CE Family Product Manual, Rev. [. . . ]