User manual MACKIE SDR24-96

[. . . ] 24/96 SDR 24 Operation Guide 24 TRACK/24 BIT DIGITAL AUDIO RECORDER SDR ERROR 44. 1k TC VARI 48k X2 96 HIGH RESOLUTION NON-LINEAR RECORDER 16 BIT 24 BIT HOURS MINUTES SECONDS FRAMES EXT CLOCK PROJECT: Feel the Love AVAIL: 02:27:26 on EXT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 SELECT SELECT SELECT SELECT POWER DELETE LAST TRACK PROJECT EDIT SETUP AUTO TAKE T-CODE CHASE REWIND FAST FWD STOP PLAY RECORD LOCATE STORE LOOP PUNCH REHRSE ALL INPUT AUTO INPUT 24 TRACK/24 BIT DIGITAL AUDIO HARD DISK RECORDER SDR 24/96 CAUTION AVIS 12. Lightning -- Unplug the SDR 24/96 during lightning storms or when unused for long periods of time. Note that this Mackie product is not completely disconnected from the AC mains service when the power switch is in the OFF position. Grounding and Polarization -- To prevent electric shock, do not use the SDR24/96 polarized plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. [. . . ] 1 press: Slow wind; 20X speed after four seconds 2 presses: 60X speed 3 presses: 180X speed 4 presses: 540X speed 5 presses: 1620X speed Stop STOP brings the "tape" to an immediate halt. If there are unsaved recording passes, the recording passes and project file are automatically saved to disk. When the transport is already stopped, pressing STOP twice within one second moves the current locator to the beginning of the project. 26 SDR 24/96 Operation Guide Scrub When the transport is already stopped, pressing and holding the STOP button for one second puts the transport into scrub mode. The STOP and PLAY LEDs light simultaneously and Entering scrub mode appears in the display. Use the REWIND and FAST FWD buttons to scrub the transport forward and backward. Press STOP or PLAY to return to normal mode. Play PLAY puts the SDR24/96 into play from any state (as if you didn't know). PLAY also punches out of record and cancels master record standby while leaving the Transport in play. Record The master RECORD button must be pressed along with PLAY to enter record mode. The master record LED blinks if there are no tracks armed (Record Ready buttons), or not within the Autopunch zone when Autopunch is activated (see page 37). When One Button Punch is activated (SETUP:Record:Page Right:RecBt), recording can be toggled during play by pressing only the RECORD button. Serial 9-Pin The SERIAL 9-PIN connector on the rear panel of the SDR24/96 is provided for connecting transport controllers that use the EIA RS-422 serial data communication standard. The following transport functions can be controlled through the Serial 9-Pin connection: Stop, Play, Rec, Fast Forward, Rewind, and Scrub. Time Display EXT CLOCK HOURS MINUTES SECONDS FRAMES The Current Time display shows the exact position of the SDR24/96's "playback head. " In the current version, the time format can be displayed only in SMPTE time (HH:MM:SS:Frames). Transport Menu The SDR24/96 transport menu allows you to set locate points, offsets, and enable AutoPlay. Locate Times The Locate option allow you to enter the time for Locates 1-4. To set the Locate time: 1. Press SETUP to enter the SETUP MENU. SETUP SETUP MENU > Record I/O Sync Transp TRANSPORT OPTIONS > Loc1 Loc2 Loc3 Loc4 Operation Guide 2. Select Zero to reset the Locate point to zero. LOC1: 00:12:34:56 > Zero OK Cancel < LOC1: 00:12:34:56 << >> Inc Dec 5. Use the increment (Inc) and decrement (Dec) buttons to change the highlighted numeral. button when finished, and then select OK to save Current Locator Time You can change the current locator time by pressing the PLAY, REWIND, FAST FWD, or LOCATE buttons. You can also change it in the Transport menu. To change the current locator time: 1. Select Zero to reset the current locator time to zero. SETUP SETUP MENU > Record I/O Sync Transp TRANSPORT OPTIONS > Loc1 Loc2 Loc3 Loc4 < TRANSPORT OPTIONS > CurLoc TrOf RelOf RelMd CURLOC: 00:13:57:24 > Zero OK Cancel < CURLOC: 00:13:57:24 5. Press Page Right to change the << >> Inc Dec current locator time. A blinking cursor appears over the first numeral of the current locator time. Use the increment (Inc) and decrement (Dec) buttons to change the highlighted numeral. Press the Page Left button when finished, and then select OK to save the new locator time. Transport Offset Transport offset is a preset amount of time that is added to the transport locator positions displayed. For example, if the transport offset is set to 00:01:00:00, the rewind function will stop at 00:01:00:00 instead of 00:00:00:00. The transport offset time is added to all locates, and to incoming and outgoing LTC and MTC. To set the transport offset time: 1. [. . . ] Mackie is not responsible for any damage that occurs due to non-factory packaging. boxes), daytime phone number, RA number, and a detailed description of the problem, including how we can duplicate it. Ship to this address: Mackie Designs SERVICE DEPARTMENT 16140 Wood-Red Rd. Ask Tech Support for current turn-around times when you call for your RA number. [. . . ]