User manual MACKIE PATX60 QUICK GUIDE

[. . . ] Strip the speaker wiring back about 1/2", loosen the screw enough to loop the wire around the shaft of the screw (clockwise), and tighten down the screw with a slot-head screwdriver. Note: Make sure the taps on the speakers add up to no more than the rated power for the amplifier being used. Connecting the PATX60 to a Constant-Voltage Distribution System In a constant-voltage distribution system, all the speakers are connected in parallel. [. . . ] Water and Moisture--This Mackie Industrial product should not be used near water ­ for example, near a bathtub, washbowl, 30W 60W NC COM 30W 60W NC COM CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE INDUSTRIAL · MADE IN ITALY · COPYRIGHT ©2000 · THE FOLLOWING ARE TRADEMARKS/REGISTERED TRADEMARKS OF MACKIE DESIGN INC. : "MACKIE" "MACKIE INDUSTRIAL" & THE "RUNNING MAN" FIGURE , , CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE INDUSTRIAL · MADE IN ITALY · COPYRIGHT ©2000 · THE FOLLOWING ARE TRADEMARKS/REGISTERED TRADEMARKS OF MACKIE DESIGN INC. : "MACKIE" "MACKIE INDUSTRIAL" & THE "RUNNING MAN" FIGURE , , SERIAL NUMBER MANUFACTURING DATE SERIAL NUMBER MANUFACTURING DATE CAUTION: SUSPENDING THIS SYSTEM SHOULD BE DONE BY QUALIFIED TECHNICIANS FOLLOWING APPROPRIATE SAFETY STANDARDS CAUTION: SUSPENDING THIS SYSTEM SHOULD BE DONE BY QUALIFIED TECHNICIANS FOLLOWING APPROPRIATE SAFETY STANDARDS sink, in a damp cellar, near a swimming pool, etc. Foreign bodies and liquids--Be careful not to allow any foreign bodies or liquids to get into this Mackie Industrial product. Technical service--The user should never attempt to make any repairs on this Mackie Industrial product unless otherwise indicated in the instruction manual. Installation--Do not install this Mackie Industrial product in any way that is not indicated in the instruction manual. Respect the safety standards--The entire sound system must be created in compliance with the current standards and laws regarding electrical systems. 70V CONSTANT-VOLTAGE DISTRIBUTION SYSTEM www. mackieindustrial. com 16220 Wood-Red Road NE Woodinville, WA 98072 TEL +888. 337. 7404, FAX +425. 487. 4337 , industrial@mackie. com UK +44. 1268. 571. 212, FAX +44. 1268. 570. 809 +info@rcf-uk. com ITALY +39. 0522. 354. 111, FAX +39. 0522. 926. 208 +industrial@rcf. it FRANCE +33. 3. 8546. 9160, FAX +33. 3. 8546. 9161 +rcf. commercial@wanadoo. fr GERMANY +49. 2572. 96042. 0, FAX +49. 2572. 96042. 10 +industrial@mackie. de Part No. Printed in Italy. Front Panel Features 70V Connections When using the PATX60 with a 70V distribution system, calculate the power usage with the top numbers for the taps (15W, 30W, 60W). 100V Connections When using the PATX60 with a 100V distribution system, calculate the power usage with the bottom numbers for the taps (30W, 60W). WARNING: DO NOT USE THE TAP LABELED NC NEXT TO THE COM TERMINAL IN A 100V SYSTEM. Security Cover After connecting the speaker wiring to the screw terminals, install the security cover to insulate the connections. Installing the PATX60 1. Remove the six screws securing the connector plate to the back of the PACX81, PA261, or PA281 with a #2 Phillips screwdriver. Red Black + 4 IN-OUT (For use with the PA261 and PA281) RED K PA 261 VISION SERIES CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE INDUSTRIAL · MADE IN ITALY · COPYRIGHT ©1999 · THE FOLLOWING ARE TRADEMARKS/REGISTERED TRADEMARKS OF MACKIE DESIGN INC. : "MACKIE" "MACKIE INDUSTRIAL" , , & THE "RUNNING MAN" FIGURE IN-OUT CAUTION: SUSPENDING THIS SYSTEM SHOULD BE DONE BY QUALIFIED TECHNICIANS FOLLOWING APPROPRIATE SAFETY STANDARDS +1/­1FULL RANGE 200W-4 SERIAL NUMBER MANUFACTURING DATE ­ PA 261 VISION SERIES + 8 RED BLACK IN CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE INDUSTRIAL · MADE IN ITALY · COPYRIGHT ©2000 · THE FOLLOWING ARE TRADEMARKS/REGISTERED TRADEMARKS OF MACKIE DESIGN INC. : "MACKIE" "MACKIE INDUSTRIAL" , , & THE "RUNNING MAN" FIGURE (For use with the PACX81) OUT CAUTION: SUSPENDING THIS SYSTEM SHOULD BE DONE BY QUALIFIED TECHNICIANS FOLLOWING APPROPRIATE SAFETY STANDARDS FULL RANGE 200W-4 SERIAL NUMBER MANUFACTURING DATE 4. Connect the two red wires to the "+" terminal on the PATX60 transformer, and connect the two black wires to the "­" terminal, as shown in the above illustration. Remove the connector panel, being careful not to damage the gasket surrounding the opening in the back of the cabinet. [. . . ] When using with a 70V distribution system, connect either the 15W, 30W, or 60W terminal as indicated by the top markings to the "+" side of the 70V system, and connect the COM terminal to the "­" side of the 70V system. When using with a 100V distribution system, connect either the 30W or 60W terminal as indicated by the bottom markings to the "+" side of the 100V system, and connect the COM terminal to the "­" side of the 100V system. PATX 60 VISION SERIES 15W 30W 60W COM 70V 100V 70V 100V 3. 2­ Black 2+ To 1­ 2­ SERIAL NUMBER MANUFACTURING DATE To 1­ 2+ 1­ CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE INDUSTRIAL · MADE IN ITALY · COPYRIGHT ©2000 · THE FOLLOWING ARE TRADEMARKS/REGISTERED TRADEMARKS OF MACKIE DESIGN INC. : "MACKIE" "MACKIE INDUSTRIAL" & THE "RUNNING MAN" FIGURE , , To 1+ 1+ 1­ 30W 60W NC COM Red To 1+ 1+ IO VIS IES R SE 60W PATX N DO NOT use the NC terminal in a 100V system. 70V 100V CAUTION: SUSPENDING THIS SYSTEM SHOULD BE DONE BY QUALIFIED TECHNICIANS FOLLOWING APPROPRIATE SAFETY STANDARDS 70V 100V 15W COM 60W 30W Red OUT IN +-+Black IE MACK WING . : LLO ED BY TUR · THE FO IGN INC NUFAC 000 IE DES T ©2 MACK N" FIGURE D MA MA D, AN PYRIGH S OF ING ARK SIGNE · CO , DE ITALY TRADEM "RUNN TE D EIVED DE IN , & THE G DA CONCL · MA EGISTERE RIAL" TURIN S/R INDUST RIA FAC UST ARK IND DEM "MACKIE MANU TRA , ARE ACKIE" "M ER NUMB SERIAL To OUT- To IN+ To OUT+ To IN- D ALIFIEDS BY QU NDAR ION: DONE STA ETY BE CAUT ULD ATE SAF SHO PRI TEM RO IS SYS G APP WIN G TH DIN FOLLO PEN SUS ICIANS HN TEC [. . . ]