User manual MACKIE ONYX80

[. . . ] PREMIUM LIVE ANALOG MIXERS w/PERKINS EQ & ONYX MIC PREAMPS OWNER'S MANUAL ONYX 80 SERIES Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. [. . . ] When the PAN control is centered, the signal is sent equally to the left and right outputs. The signal sent to the MAIN OUTS is after the Group Insert, Fader, and MUTE switch. MAIN MIX L R L R MAIN MIX 39. AFL Solo Switch The AFL switch allows you to hear the Aux Send signal through your headphones or monitor outputs. This comes after the Aux Send GAIN control, so you can hear the relative signal level on each Aux Send. When you engage the AFL switch on two consecutive odd/even Aux Sends (i. e. , 1 and 2, 3 and 4, etc. ), the soloed signal appears in stereo in the headphones and monitor outputs. This is useful when you are using a pair of Aux Sends in stereo to feed an in-ear monitoring system. PAN PAN GROUP MUTE 1 GROUP MUTE 2 42. When the MUTE switch is pushed in on a Group, you can still solo the Group signal (see AFL Solo Switch [39] ahead). dB dB 10 10 5 OL +10 5 OL +10 U 0 -20 U 0 -20 43. GROUP Fader This fader controls the Group's signal level, from off to unity gain at the "U" marking, on up to 10 dB of additional gain. 5 5 10 10 20 20 44. Signal Level LEDs These LEDs indicate the Group's signal level after the Fader and MUTE switch. So if the MUTE switch is pushed in or the Faders are down, the Signal Level LEDs won't light. 30 30 40 50 60 O O 40 50 60 O O STEREO AFL AFL 16 ONYX 80 SERIES 45. AFL Solo Switch The AFL switch allows you to hear the Group signal through your headphones or monitor outputs. This comes after the Group Fader and before the MUTE switch, so you can hear the relative signal level on each Group even when they are muted. When you engage the AFL switch on two consecutive odd/even Groups (i. e. , 1 and 2, 3 and 4, etc. ), the soloed signal appears in stereo in the headphones and monitor outputs. This is useful when you are using a pair of Group Sends in stereo to feed an in-ear monitoring system. If you engage a PFL solo switch on a mono or stereo channel, the AFL solo is disconnected from the headphones and monitor outputs and replaced with the PFL signal. The Rude Solo LEDS below the SOLO meters indicate which solo mode is active. Metering, Matrix, and Power LEDs 47. POWER Indicators These four LEDs indicate the status of the internal power supply voltages. The +15V and ­15V supplies power the audio circuits, the +48V is the phantom power applied to the XLR MIC inputs (when the 48V switch is pushed in on the channel strips), and the ­12V supply powers some internal relay circuits and the lamp connectors. When all four LEDs are lit, you know that the internal power supply (or the external redundant power supply, if connected) is operating correctly. Owner's Manual 48. GROUP/AUX FLIP Switch This switch "flips" the controls for the Aux Sends and the Group Sends, so that the Group Faders control the Aux Send levels, and the Aux Send GAIN controls adjust the Group levels. The Group signals still appear at the GROUP SEND outputs and the Aux Send signals still appear at the AUX SEND outputs. This allows you to use the long-throw (100 mm) Group Fader to make more precise settings for the Aux Sends, if required. [. . . ] Ship the product in its original shipping carton, freight prepaid to the authorized service center. The address of your closest authorized service center will be given to you by Technical Support. IMPORTANT: Make sure that the Service Request Number is plainly written on the shipping carton. LOUD Technologies reserves the right to inspect any products that may be the subject of any warranty claims before repair or replacement is carried out. [. . . ]