User manual MACKIE HRS150

[. . . ] HRS150 HIGH RESOLUTION POWERED SUBWOOFER OWNER'S MANUAL INPUT/OUTPUT POWER SUB BYPASSED FILTER BYPASS FLAT 15Hz STANDARD SETTINGS SUBSONIC FILTER SUBSONIC FILTER FILTER BYPASS FILTER SELECT LFE GAIN INPUT SENSITIVITY BYPASS FILTER SELECT LFE GAIN INPUT SENSITIVITY ( 5. 1) FILTER IN FULL RANGE VARIABLE 110Hz ELIPTICAL LFE GAIN POLARITY +10dB SUB SAT 0dB NORMAL 80Hz CROSSOVER CONTROLS 0° 180° OFF NORMAL POLARITY LEFT SUB SAT IN (MONO) OUT 80Hz THX PM3 SETTINGS SUBSONIC FILTER 55Hz 110Hz FILTER BYPASS BYPASS FILTER SELECT L L LFE GAIN INPUT SENSITIVITY CROSSOVER (N/A) IN R SUB SAT OUT R POLARITY NORMAL SUB SAT 80Hz 80Hz CROSSOVER CONTROLS 55Hz 110Hz CROSSOVER IN OUT RIGHT SLAVE/MASTER SLAVE IN S M MASTER OUT ON POWER POLARITY & INPUT SENSITIVITY ACTIVE PROCESSED SIGNAL SUBWOOFER BYPASS FOOTSWITCH REMOTE INDICATOR 120 VAC, 60 Hz, 950 WATTS OPEN - SUB ON, L/R BASS MANAGED CLOSED - SUB DEFEAT, L/R FULL RANGE *MAX OPEN CIRCUIT 24V *MAX CLOSED CIRCUIT 1A REMOTE INDICATOR CIRCUIT CLOSED WHEN SUB BYPASSED *TO INSURE PRODUCT SAFETY, POWER SUPPLIES MEETING CLASS-2 INSULATION REQUIREMENTS SHOULD ONLY BE USED WITH THIS CONNECTOR "MACKIE", "FR SERIES", AND THE "RUNNING MAN" FIGURE ARE REGISTERED TRADEMARKSOF MACKIE DESIGNS, INC. "THX PM3" AND "LUCASFILM" ARE TRADEMARKS OF LUCASFILM, LTD. USED BY PERMISSION CAUTION HEATSINK SURFACE HOT AVOID CONTACT CAUTION HEATSINK SURFACE HOT AVOID CONTACT CAUTION TM RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS INTERNAL AMPLIFICATION 1050W EQUIPMENT TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED PERSONNEL. AVIS: RISCQUE DE CHOC ÉLECTRIQUE -- NE PAS OUVRIR SERIAL NUMBER MANUFACTURING DATE DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA ©2002 MACKIE DESIGNS INC. [. . . ] This allows you to record the LFE channel at ­10 dB relative to the other channels, as specified by AC-3 encoding standards. For Playback: Push this switch in to add 10 dB of gain to the subwoofer signal. This is useful for home theater applications where the LFE channel requires additional gain to balance with the other channels in the surround sound system. INPUT SENSITIVITY INPUT SENSITIVITY FILTER BYPASS OFF NORMAL FILTER BYPASS FILTER IN FULL RANGE THX = FULL RANGE This switch bypasses the built-in low-pass filters (variable and elliptical). Push this switch in when connecting an LFE or subwoofer output signal from a mixer or preamp to the LEFT(MONO) and/or RIGHT inputs, to avoid "double-filtering" the low-frequency signal. Note that the LEFT(MONO) and RIGHT OUTputs are still high-pass filtered and affected by the CROSSOVER controls. THX = NORMAL The HRS150 expects a line-level signal at its input connectors. · The sensitivity is 89 dB SPL at one meter with a 100 mV (­17. 8 dBu) input signal, with the INPUT SENSITIVITY control set to its NORMAL position (in other words, wide open). · The HRS150 is designed to operate with a nominal +4 dBu signal when the INPUT SENSITIVITY control is in the NORMAL position. · Refer to the QUICK START section on page 4 for the level-setting procedure. 8 POLARITY 0° 180° POLARITY THX = 0° This switch reverses the polarity of the signal going to the subwoofer amplifier by 180º. It has no effect on the signal at the LEFT and RIGHT OUT or the MASTER OUT. Listen to the overall blend of the subwoofer with the rest of the system, and select the switch position that gives you the best sound. INPUT/OUTPUT POWER SUB BYPASSED FLAT 15Hz SUBSONIC FILTER FILTER BYPASS FILTER SELECT LFE GAIN INPUT SENSITIVITY THX PM3 SETTINGS SUBSONIC FILTER FILTER IN FULL RANGE VARIABLE 110Hz ELIPTICAL 0dB FILTER BYPASS FILTER SELECT LFE GAIN INPUT SENSITIVITY (N/A) LEFT AND RIGHT INPUTS Balanced XLR female and unbalanced RCA female connectors are provided for the left and right inputs. Connect the full-range line-level signal from the mixer or preamplifier to one of these input jacks. The connectors are wired as follows (per the AES/IEC standard): XLR RCA Hot (+) Pin 2 Tip Cold (­) Pin 3 -- Shield (Ground) Pin 1 Shield If connecting a single subwoofer or LFE output to the HRS150, use the LEFT (MONO) input with the FILTER BYPASS switch pushed in. +10dB NORMAL POLARITY SUB SAT 80Hz 0° 180° OFF NORMAL POLARITY CROSSOVER CONTROLS LEFT SUB SAT IN (MONO) OUT 80Hz 55Hz 110Hz CROSSOVER L L LEFT AND RIGHT OUTPUTS Balanced XLR male and unbalanced RCA female connectors are provided for the line-level left and right high-pass outputs. Connect these to the inputs of the main speakers (if they are powered speakers) or to the inputs of the amplifier powering the main speakers. The low-pass output from the crossover goes to the internal power amplifier in the HRS150, while the high-pass output goes to these output jacks. SUB SAT IN R OUT R 80Hz 55Hz 110Hz CROSSOVER IN OUT RIGHT SLAVE/MASTER SLAVE IN S M MASTER OUT CROSSOVER SUB SAT POLARITY & INPUT SENSITIVITY ACTIVE PROCESSED SIGNAL 80Hz SUBWOOFER BYPASS FOOTSWITCH REMOTE INDICATOR 55Hz 110Hz CROSSOVER OPEN - SUB ON, L/R BASS MANAGED CLOSED - SUB DEFEAT, L/R FULL RANGE *MAX OPEN CIRCUIT 24V *MAX CLOSED CIRCUIT 1A REMOTE INDICATOR CIRCUIT CLOSED WHEN SUB BYPASSED THX = 80 Hz This adjusts the crossover frequency for the built-in 24 dB/octave Linkwitz-Riley variable crossover. The crossover frequency can be adjusted from 55 Hz to 110 Hz. *TO INSURE PRODUCT SAFETY, POWER SUPPLIES MEETING CLASS-2 INSULATION REQUIREMENTS SHOULD ONLY BE USED WITH THIS CONNECTOR 9 Frequencies below the crossover frequency are sent to the subwoofer, and frequencies above the crossover frequency are sent to the LEFT and RIGHT OUTputs, which are connected to the main/satellite speakers. Set the crossover frequency to the lowest frequency response rating of the main/satellite speakers. across the tip/sleeve when the internal relay is open, and a maximum 1 amp of current when the relay is closed. CAUTION: There is an internal 1A fuse to protect the REMOTE INDICATOR circuit. Exceeding 1A of current may blow the internal 1A fuse. MASTER OUT/SLAVE IN Balanced XLR and unbalanced RCA female connectors are provided for the MASTER OUT/ SLAVE INputs. Use these for daisy-chaining two HRS150s by connecting the MASTER OUT jack from the first subwoofer to the SLAVE IN jack on the second subwoofer (see note below). The SLAVE IN bypasses all filtering, but is affected by the POLARITY and INPUT SENSITIVITY settings. The MASTER OUT is post-filtering (variable and elliptical crossover, subsonic filter, and LFE gain) and pre- POLARITY and INPUT SENSITIVITY. Note: You cannot daisy-chain more than one additional subwoofer using these connections. [. . . ] More information on packing can be found in the Service section of this manual. Do not use "packing peanuts, " shredded newspapers, or other material with small particles, old underwear, or socks. Also include a note explaining exactly how to duplicate the problem, a copy of the sales receipt with price and date showing, and your return street address (no P. O. If we cannot duplicate the problem at the Mackie Factory or establish the starting date of your Limited Warranty, we may, at our option, charge for service time. [. . . ]