User manual MACKIE D8B3.0

[. . . ] DIGITAL 8·BUS OWNER'S MANUAL Version 3. 0 TM MACKIE'S 56-INPUT, 72-CHANNEL, FULLY AUTOMATED DIGITAL AUDIO MIXING CONSOLE 8. Power Sources -- This Mackie product should be connected to a power supply only of the type described in these operating instructions or as marked on this Mackie product. Power Cord Protection -- Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit this Mackie product. Object and Liquid Entry -- Care should be taken so that objects do not fall into and liquids are not spilled into this Mackie product. [. . . ] The specific hookups for each D8B and HDR24/96 I/O card are shown below. 2. Connect three snakes between the HDR24/96 Outputs (top connector) and the corresponding D8B Tape Inputs (bottom connector). HDR24/96 Settings 1. It is not necessary to set the D8B and HDR24/96 to the same Sample Rate since, with analog connections, the sample clocks on the two units are not synchronized. Console Settings 1. Set the D8B Sample Rate to 44. 1kHz or 48kHz, and set the Apogee Clock to Internal (in the Digital I/O Setup window). Analog Hookup to HDR24/96 (AIO·8) This example describes the analog hookup for the D8B­HDR24/96 combination. Cables & Hardware (3) AIO·8 cards for HDR24/96 (3) AIO·8 cards for D8B (6) DB25 to DB25 analog snakes Hookup 1. Connect three snakes between the HDR24/96 Inputs (bottom connector) and the corresponding D8B Tape Outputs (top connector). This example describes the hookup for the D8B console equipped for analog I/O. HDR 24/96 AIO·8 Cards ANALOG I/O ANALOG I/O ANALOG I/O Digital 8·Bus (6) DB25 to DB25 Analog Snakes AIO·8 Cards ANALOG I/O ANALOG I/O ANALOG I/O OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT Note: Some older AIO·8 cards have the Input jack labeled as "From Tape" and the Output jack labeled as "To Tape. " Otherwise, they operate identically. long story. INPUT INPUT INPUT INPUT INPUT TAPE IN/OUTS TAPE IN/OUTS D8B Manual · Chapter 4 · page 112 INPUT OUTPUT TDIF Hookup to HDR24/96 (DIO·8) Cables & Hardware (3) DIO·8 cards for HDR24/96 (3) DIO·8 cards for D8B (1) Clock I/O card for D8B (3) TDIF cables (1) 75 BNC word clock cable DIO·8 Sync out) to the HDR24/96 Word Clock In. To make the HDR24/96 the clock master, connect its Word Clock Out to the D8B Word Clock In. HDR24/96 Settings 1. Set the Tape Input format for each DIO·8 card to TDIF, and the Tape Output format to TDIF. If the HDR24/96 is the clock master, set the Sample Clock to Internal; if it is a clock slave, set it to Word Clock and depress the 75 termination switch on the Sync card. Set the Sample Rate to 44. 1kHz or 48kHz according to your preference. Hookup 1. Connect the three TDIF cables between the corresponding TDIF jacks on the HDR24/96 and D8B. To make the D8B the clock master, connect its Word Clock Out (not TDIF Hookup with DIO·8 Apogee Clock I/O Card Word Clock Out APOGEE SYNC APOGEE DIGITAL I/O DIO·8 Cards APOGEE DIGITAL I/O APOGEE DIGITAL I/O TDIF Connection Word Clock Out TDIF TDIF TDIF APOGEE Digital 8·Bus ADAT OPTICAL ADAT OPTICAL ADAT OPTICAL OUT OUT IN IN IN OUT Word Clock In Word Clock In TDIF Cables (DB25) SYNC SYNC Word Clock Out (HDR24/96 as Master) WARNING NOT Word Clock Out (D8B as Master) HDR Sync Card APOGEE DIGITAL I/O APOGEE DIGITAL I/O APOGEE DIGITAL I/O ADAT OPTICAL ADAT OPTICAL ADAT OPTICAL IN IN IN Depress the Termination button if the HDR24/96 is set to Slave Use one only TDIF TDIF TDIF SYNC HDR 24/96 TDIF Connection OUT OUT OUT DIO·8 Cards Word Clock In Word Clock Out SYNC SYNC S C SYNC D8B Manual · Chapter 4 · page 113 Console Settings 1. Set the Tape Input and Tape Output format for each DIO·8 card to TDIF. If the D8B is the clock master, set the Sample Rate to either 44. 1kHz or 48kHz, and set the Apogee Clock to Internal (in the Digital I/O Setup window). Set the Sample Rate to match the Sample Rate selected on the HDR24/96. ADAT Optical Hookup to HDR24/96 (DIO·8 or OPT·8) Cables & Hardware (3) DIO·8 or OPT·8 cards for HDR24/96 (3) DIO·8 or OPT·8 cards for D8B (1) Clock I/O card for D8B (6) ADAT Optical cables (1) 75 BNC word clock cable Hookup 1. Connect three ADAT Optical cables from the HDR24/96 Optical Outputs to the Optical Inputs on the corresponding D8B I/O cards. Connect three ADAT Optical cables from the HDR24/96 Optical Inputs to the Optical Outputs on the corresponding D8B I/O cards. When ADAT Optical is used, the D8B must have a Clock I/O card installed. To make the D8B the clock master, connect its Word Clock Out to the HDR24/96 Word Clock In. To make the HDR24/96 the clock master, connect its Word Clock Out to the D8B Word Clock In. HDR24/96 Settings 1. [. . . ] 76 V V-Pot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13, 26, 29, 34, 35, 43, 44, 48 V-Pot Assign Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Aux 1­8 Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Aux 11­12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]