User manual MACKIE AM4160 DATASHEET

[. . . ] Microphone Input 1 can be switched to line level, set to have priority over all inputs, and can be activated by either VOX with an adjustable threshold or a contact closure. Activation of any microphone override provides 18Vdc (300mA) at a barrier connector on the rear panel, which may be used to drive LEDs or relays. Two unbalanced, stereo Aux inputs are internally summed to mono and selected by a switch on the front panel. [. . . ] at 7kHz 115/230Vac (±5%), 50/60Hz, 550VA, DC (24V battery) 14A/Hr Environment Maximum Ambient: Physical Dimensions (HxWxD): Weight: Finish: Warranty 3 years, parts & labor one-time, no-fault repair policy Accessories A1708 Three Chime Card 131°F (55°C), Non-precipitating humidity 3. 46" x 17" x 12. 4" (88mm x 431mm x 314mm) 28. 65lbs. (13kg) Black painted or treated steel, white nomenclature AM4160 Noise: Equalization Output: Inputs 2­4: Audio Inputs Microphones: Three, active balanced XLR, LoZ, 1. 3mV, 24V phantom powering with on-off switch Microphone/Line: One, active balanced XLR and parallel barrier, switched mic/line; Mic: LoZ, 1mV, Line: 80mV Line Level: Three, unbalanced, RCA connectors. Two each, left and right (summed) Aux, either pair selectable via front-panel switch, 100mV; One, Main (signal processing return), 775mV Audio Outputs Number of Channels: Low Impedance: Constant Voltage: Line Level: One 4 25V, 50V, 70V, 100V Barrier connectors One, signal processing output 2. 5V, 600 Two, tape (auxiliary) outputs 0­2. 2V, RCA connectors LED relay output, aux DC output: 18Vdc (300mA) activated by priority Priority switch input, dry contact closure barrier connectors Power switch, master Volume, Inputs 1­4, Aux level, Aux 1/2 switch, Treble shelving, Bass shelving Tape output level, Voice priority threshold, Chime output level (if installed), 24V phantom on/off switch, H-P Filter in/out switch, L-P Filter in/out switch, Source Voltage Selector switch Control Inputs & Outputs DC Outputs: Inputs: Controls Front Panel: Rear Panel: 2 O FoF46 PAGES S PAGE 3 AM 4160 - P. A. AMPLIFIER OVERLOAD SIGNAL PEAK ON AM4160 O FoF46 PAGES S PAGE INPUT LEVELS AUX EQ VOLUME HIGH 4 2 4 6 2 1 9 0 10 8 3 7 6 5 INPUT 1 AUX 6 7 82 1 9 0 10 0 -10 -10 10 +10 +10 9 8 8 1 8 8 8 6 66 3 7 1 4 4 4 2 4 6 2 5 2 2 0 0 LOW 4 6 7 82 1 9 0 10 3 3 82 5 4 5 INPUT 2 INPUT 3 INPUT 4 POWER 4 5 6 4 5 6 3 7 3 7 2 82 1 9 1 9 Integrated Mixer/Amplifier 0 10 0 10 MANUFACTURING DATE CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE INDUSTRIAL · MADE IN ITALY PATENTS PENDING · COPYRIGHT ©1999 · THE FOLLOWING ARE TRADEMARKS/REGISTERED TRADEMARKS OF MACKIE DESIGN INC. : "MACKIE" "MACKIE INDUSTRIAL" & THE "RUNNING MAN" FIGURE , , AMPLIFIER AM4160 Integrated Mixer/Amplifier Architects' and Engineers' Specifications The integrated mixer/amplifier shall have a nominal output power of at least 160W RMS. It shall operate on 115VAC or 230VAC at either 50Hz or 60Hz and have its source power supplied by a detachable IEC power cord. In addition the unit shall be capable of being directly powered by a 24Vdc source, such as storage batteries. The unit shall have a constantimpedance output to drive a 4 load at its rated output. It shall also have 25V, 50V, 70V and 100V constant-voltage outputs with like performance. Inputs to the unit shall include: at least four actively balanced microphone; two unbalanced, stereo Aux; and an unbalanced signal processing return. Outputs shall include: at least two unbalanced Tape (auxiliary) with a common, continuously variable level control; and one signal processing send. Balanced connections shall be made through XLR connectors and unbalanced connections through RCA connectors. Microphone Input 1 shall have adjustable sensitivity between mic and line, selected by a switch on the rear panel. This input shall also be programmable to completely exclude or attenuate all other inputs when its priority link is activated by either a contact closure or a VOX circuit, with a continuously adjustable threshold. The XLR connector for Input 1 shall be wired, in parallel, to a barrier strip on the rear panel. [. . . ] LED status indicators shall be provided on the front panel to indicate power, signal present at the output terminals, peak signals near clipping and an overload condition. The integrated mixer/amplifier shall be a model AM4160, manufactured by Mackie Industrial. AM4160 Electronic files for this product available at: www. mackieindustrial. com This Specification Sheet Quick-Start Manual Owner/Operator's Manual AM4160. PDF AM4160QS. PDF AM4160ML. PDF www. mackieindustrial. com 16220 Wood-Red Rd. NE, Woodinville, WA 98072 USA 888. 337. 7404, fax 425. 487. 4337, industrial@mackie. com UK +44. 1268. 571. 212, fax +44. 1268. 570. 809, info@rcf-uk. com ITALY +39. 0522. 354. 111, fax +39. 0522. 926. 208, industrial@rcf. it FRANCE +33. 3. 8546. 9160, fax +33. 3. 8546. 9161, rcf. commercial@wanadoo. fr GERMANY +49. 2572. 96042. 0, fax +49. 2572. 96042. 10, industrial@mackie. de Mackie Designs continually engages in research related to product improvement. [. . . ]