User manual LEICA TPS1100

[. . . ] Leica TPS1100 Professional Series User Manual Version 2. 2 English Electronic total stations Congratulations on your purchase of a TPS1100 Professional Series instrument. This manual contains important safety directions (refer to chapter "Safety directions") as well as instructions for setting up the product and operating it. Read carefully through the User Manual before you switch on the instrument. 2 TPS1100 - User Manual 2. 2. 1en Product identification The instrument model and the serial number of your product are indicated on the label in the battery compartment. Enter the model and serial number in your manual and always refer to this information when you need to contact your agency or authorized service workshop. Type: Serial number: Software version: Language: TPS1100 - User Manual 2. 2. 1en 3 Product identification Symbols used in this manual The symbols used in this User Manual have the following meanings: DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. [. . . ] , , Define reflectors from other manufacturers. System functions 70 TPS1100 - User Manual 2. 2. 1en Setting / defining prisms, continued MC \Define new reflector 1 Define type of reflector Ref. 1 Type : Not defined Ref. 1 Name Ref. 1 Cons CONT QUIT : : --------- mm EDM test Displays the signal strength or measurement frequency. \ EDM Return Signal Signal strength 0% Tone CONT : 75% OFF▼ ▼ FREQ 100% Distance corrections, ppm A distinction is made between atmospheric (ppm) and geometric (ppm) corrections, the sum of which is used as the final distance correction. Atmospheric correction STOP QUIT 6 10 12 21 MC The user can freely define the name and additive constant (additive constant) for three reflectors and can enter the type of reflector (prism or retro tape). It is advisable to determine the additive constant for "non Leica Geosystems prisms" on a baseline by means of an appropriate procedure. For the reflector to be available for choice, the reflector type may not be "None". Toggles between the displays of measurement frequency and signal strength. The measurement frequency display is similar to the display shown above. The stronger the signal the more the black intensity bar is extending to the right against 100%. With an already low signal distances can be measured. The atmospheric distance corrections are derived from the dryair temperature, air pressure or height over mean sea-level, and relative air humidity or wet-air temperature. \ ATMOSPHERIC CORR. : ppm atmospheric : ppm geometric : ppm total : CONT 26 12. 0 °C mBar 60. 0 % 0. 0 0. 0 0. 0 GEOM REFRA P<>E %<>T' ATM=0 QUIT Settings for the geometrical correction. TPS1100 - User Manual 2. 2. 1en 71 System functions MC Distance corrections ppm, continued Settings for the refraction correction. (Individual parameters are set to the standard atmospheric values, corresponding to the atmospheric correction ATM=0) Geometrical correction The geometrical distance correction is derived from the projection distortion and the height above the reference datum. The calculation of the geometrical ppm follows the formula for the Transversal Mercator Projection. The individual factors are: the scale factor of the line of projection (central meridian, Gauss-Krüger = 1. 0, UTM = 0. 9996, etc. ); the offset from the line of projection; the height above the reference datum (normally this is the height above mean sea-level); and an additional individual scale correction. The distance without any projection distortion is used to determine the height difference. The individually-set scale adjustment is always applied to the distance. The individual scale correction can be used to enter a total geometrical correction. \ GEOMETRIC CORR. level : ppm map projection: 0. 0 0. 0 QUIT -22. 9 GEO=0 Sets the geometrical ppm to "0. 00". The other parameters are set to "0. 00". System functions 72 TPS1100 - User Manual 2. 2. 1en MC Distance corrections ppm, continued Refraction correction The refraction correction is taken into account during the calculation of the height difference. \ REFRACTION CORR. (k) : ON 0. 13 Reduced distance corrections ppm For standard applications the distance is corrected only on account of atmospheric influences. The geometrical correction and the projection distortions are set to "0. 00". Heights are reduced with the standard refraction coefficient Activate the function "PPM Atmospheric" from the dialog "Function Selection". QUIT \ PPM Corrections Enter your correction values Atm. pressure : Temperature : 1013. 3 mbar 12. 0 °C -0. 0 QUIT Measurement & recording (REC) MEAS\ Measurement & Record Point Id : 1 Attrib. : 1. 500 Hz :286°55'50" V : 91°16'20" Horiz. Dist. : ----ALL DIST REC : : : : MC m m m m m m 6 10 12 21 26 SetHz >DISP ----------------- MC Elev. Diff. East North Elev. INPUT Del B I<>II INDIV QUIT MC CONT DEFLT The data shown above represent the standard display mask. [. . . ] 103 PPM Corrections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 PPM entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Product identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]