User manual KOMPERNASS TRONIC KH 3002 ENERGY STATION

[. . . ] · Do not expose the energy station to any heat source whatsoever, e. g. · Do not allow children to play with the device without supervision. Charging Before using the device, satisfy yourself that the energy station, the connection cables and the mains charging adapter are in perfect condition. Prior to initial usage it must therefore be charged as described under b) or c). The battery can lose considerable capacity should you use the energy station without fully charging it beforehand! [. . . ] · you can set the main switch to "ON" ­ your device will now be supplied with power. · A green LED "Full" is illuminated as soon as the main switch is switched on and sufficient energy is available. · A red LED "Empty" is illuminated as soon as the main switch is switched on ­ but the battery is almost empty. You must first recharge the battery if the red LED "Empty" is illuminated. Otherwise the battery will be depleted, usually resulting in a considerable loss of charging capacity. Hint: Once you have established the correct connector assignment for your device, you can secure the connector with insulating tape to the receptacle so that you will immediately have a "suitable" cable for your device available the next time. -7- + - + - · Now you can pull the adapter cable connectors from both the device and the energy station. If none of the two LEDs light up after switching on, the 10 A fuse on the energy station might have blown. Changing the fuses is described in more detail in Chapter " Fuses ". Should an LED light up on the energy station after switching on but your device fail to work: · you should immediately switch off the energy station. · In this case, initially check whether the cable is correctly connected ­ and "Positive" and "Negative" have not been switched. If required, also check the fuse in your device as described in its instructions. IB_KH3002_E2497_UK_V1. qxd 17. 01. 2007 9:17 Uhr Seite 8 KH 3002 Output for 10 A An output as motor vehicle socket is available for so-called "cigarette lighter connectors" for the power supply of devices to a maximum of 10 A. Please consider that with a 10 A load the battery will be exhausted after not more than 45 minutes ­ depending on the charge condition, even much earlier. With a battery capacity of 7 Ah, this corresponds to just under 2 hours of operating time. You can roughly estimate the operating time for your device using this calculation example. Before performing any kind of connection operations, always satisfy yourself that both your device as well as the energy station are switched off · that is the main switch in the "OFF" position (centre position). In this way you can prevent damages through connection faults. a) Connecting the device Caution!Before connecting your device to the energy station, you must first ensure that "Positive" and "Negative" are not switched. · With the supplied cable the device connector is connected so that Positive is on the inside and Negative on the outside, as shown. You can - use this cable if the jack on your device is marked thus: - not use this cable if the jack on your device is marked thus: On devices with permanently connected cable with motor vehicle connector, "Positive" and "Negative" have the correct polarity. · Insert the device connector of the supplied cable in the jack on your device. · you can now set the main switch to "ON" ­ your device will now be supplied with power · A green LED "Full" will be illuminated as soon as the main switch is switched on and sufficient energy is available. -8- IB_KH3002_E2497_UK_V1. qxd 17. 01. 2007 9:17 Uhr Seite 9 KH 3002 · A red LED "Empty" will be illuminated as soon as the main switch is switched on ­ but the battery is almost empty. You will first have to recharge the battery if the red LED "Empty" is illuminated. [. . . ] · first switch the main switch to the "OFF" position. . . · and pull all cable connections between energy station and any connected devices. · If you wish to clean the mains charging adapter, pull it from the socket and from the charging jack as well. Caution!On no account must the device components be immersed in water or other liquids! [. . . ]