User manual KOMPERNASS SILVERCREST KH 2324 DAB-RADIO

[. . . ] · Do not open the casing or try to repair the appliance yourself. In this case, appliance-safety cannot be assured and the warranty is voided. Delivery Contents DAB Radio KH 2324 Power Cable Operating Manual Technical Data Rated voltage: For battery operation: 230 V / 50 Hz 6x 1, 5 V Typ C batteries (not supplied) DAB: 174 - 240 MHZ FM: 87. 5 - 108 MHZ Frequency range : Temperature range: -5 bis 40°C Safety instructions · Do not allow children to handle electrical appliances when unsupervised because they often underestimate the danger. -4- KH2324_DAB_Radio_UK. qxd 30. 03. 2006 10:41 Uhr Seite 5 KH2324 · Do not place objects containing fluids, e. g. · Do not keep the appliance in places that are exposed to direct sunlight, otherwise it may overheat and become irreparably damaged. · Never cover the ventilation slots of the appliance while it is switched on. [. . . ] Should the radio find a station group on a frequency, the name of the station group is displayed. Press the button UP o or DOWN y to switch through the stations bundled in this station group. Station Search (Auto-Tune) You can choose between two different station search methods: , , Quick Scan" and , , Full Scan". When the station search is finished, the station found first is shown in the display r. To activate the , , Quick Scan", press the button AUTOTUNE 1@ once. , , Autotune Quick Scan" appears in the display, then , , Searching. . . ". To activate , , Full Scan", hold the button AUTOTUNE 1@ pressed until , , Autotune Full Scan" is shown in the display. Afterwards, , , Searching. . . " appears in the display, until all stations have been found. To switch through the stations found, press the buttons UP o or DOWN y. If you wish to end the station search prematurely, press the button UP o or DOWN y. Autoselect If you have activated Autoselect, with the buttons UP o or DOWN y you can select a station directly. Press the button UP o or DOWN y until you have reached the desired station. When you release the button UP o or DOWN y, the station is automatically selected. If Autoselect is deactivated you must, after the selection, confirm the station chosen using the buttons UP o or DOWN y with the button SELECT i. If you do not confirm the selection, the previously selected station will be displayed again after four seconds. To activate or deactivate Autoselect, press the button UP o or DOWN y and then immediately afterwards hold down the button SELECT i until, in the display r, , , Autoselect ON" or , , Autoselect OFF" is shown. FM-Mode Press the button , , DAB/FM" w, to switch between DAB and FM Mode. In the display r , , Switching to FM" or , , Switching to DAB" appears. Manual Station Search Press the button UP o or DOWN y to switch through the frequencies. The radio starts the station search and halts as soon as the next higher station is found. -8- KH2324_DAB_Radio_UK. qxd 30. 03. 2006 10:41 Uhr Seite 9 KH2324 Hold the button AUTOTUNE 1@ down. The radio starts the station search and halts as soon as the next lower station is found. Should an RDS-Signal (Radio Data System) be transmitted from the station found, additional information such as station name, time and song title are displayed. Through further pressing on the button SELECT i you can choose between , , Auto" or , , Mono". If however only a weak radio signal is received, manual switching to Mono can improve the quality. Note: If you recall a saving position in DAB Modus on which a station is not yet saved, , , PRESET 1/2/3/4 empty" is shown in the display. Display Through repeated pressing of the button INFO u you can call up various information details about the radio programme: In DAB Mode: Ensemble/Multiplex Signal Strength Time/Date DLS Programme Type Alarm Status Save / Recall Stations You can save four stations in FM Mode, as well as four station groups in DAB Mode. [. . . ] Please include a copy of your purchase receipt with all postal submissions. The device should be packed in a manner that is safe for transport and the RMA number should be directly visible. Note: Warranty claims are only valid for material and manufacturing defects. Warranty claims are not valid · for parts subject to wear and tear. [. . . ]