User manual KOMPERNASS PARKSIDE PEBH 900 ROTARY PERCUSSION DRILL

[. . . ] By doing this you will be able to work in complete safety and produce better results. We hope you enjoy using your drill. FEATURES OF THE PEBH 900 Chuck Locking/unlocking cap Depth stop Function selector Ventilation slots TECHNICAL INFORMATION Nominal power: Nominal voltage: No load speed: Blows per minute max. : Max. hole diameter: 900 W 230 V ~ 50 Hz no 0 - 1. 100 /min 0 - 5. 800 /min 24 mm in concrete 13 mm in steel 30 mm in wood II 3, 3 kg Sound pressure level: Sound power level: Vibration: Lp = 099, 6 dB(A) Lw = 112, 6 dB(A) 8, 5 m/s2 ON / OFF trigger Speed control wheel Forward/reverse selector Trigger lock button Auxiliary side handle Protection class: Gewicht: Wear ear defenders ! IMPORTANT SAFETY ADVICE To be read in conjunction with the advice in the accompanying booklet on safety before using for the first time. To avoid causing damage and danger to life, before starting work check the surface you are about to drill (e. g. [. . . ] You should be able to hear clearly the tool engaging if it has been inserted correctly. The device is designed so that tool has a certain amount of radial and axial play. The centring takes place automatically once the motor is started. REMOVING TOOL To remove the tool, pull the locking/unlocking cap backwards again and remove the tool. ADDITIONAL CHUCK FOR STRAIGHT SHANK DRILL BITS INSTALLING ADDITIONAL CHUCK FOR STRAIGHT SHANK DRILL BITS To install the additional chuck for straight shank drill bits (see Fig. , pull the locking/unlocking cap backwards and insert the additional chuck. You should be able to hear clearly the additional chuck engaging if it has been inserted correctly. REMOVING ADDITIONAL CHUCK FOR STRAIGHT SHANK DRILL BITS To remove the additional chuck, pull the locking/unlocking cap backwards again and remove the additional chuck. 5 www. kompernass. com +++ www. kompernass. com +++ www. kompernass. com +++ SELECT FUNCTION WARNING !Only use / set the function selector after the motor has reached a standstill. You can set the function selector to the symbol appropriate to the area of use. There are three function settings as follows: CHISELLING ROTARY PERCUSSION DRILLING DRILLING / SCREWING SELECT DIRECTION OF ROTATION WARNING !Only use / set the forward / reverse selector after the motor has reached a standstill. Note: The maximum speed for heavy work is only available in forward mode. The drill always works at a lower speed in reverse mode. PRESELECT SPEED WARNING !Only use / set the speed control wheel after the motor has reached a standstill. You can use the speed control wheel to preselect the operating speed to the exact value appropriate to your work. In addition, it allows you to avoid the drill bit slip ping and breaking material out around the hole whilst drilling. Note: If you select a low speed, this means the ON / OFF trigger will only press in a limited amount (as a result of the reduced speed pre selected). If you need the maximum power for your work, use the highest preselected speed (turn speed control wheel down ( )). LOW (­) SPEED: HIGH (+) SPEED: turn the speed control wheel turn the speed control wheel up ( ) down ( ) USING THE AUXILIARY HANDLE Warning !On safety grounds, make sure you always use the auxiliary side handle whilst operating the PEBH rotary percussion drill. You can alter the position of the auxiliary side handle by loosening the wingnut and swivelling the handle. Recommendation: Set the handle in the horizontal position (at 90° to the drill body). [. . . ] Damage caused due to improper handling as well as regular wear of the parts are not covered by this warranty. Beaver Electronic Services · The Lodge, Premier Business Park Long Street, Walsall · West Midlands, WS2 9DY Tel. : 08707876177 · Fax: 01922/725417 Warranty This piece of equipment is covered by a 36-month warranty as of the date of purchase. The equipment was produced with the greatest of care and underwent thorough testing before delivery. In the unlikely event of detecting a functional defect, please return the equipment in its original packaging with the proof of purchase (if available) to the closest service address. [. . . ]