User manual KOMPERNASS PARKSIDE KH 3127 PRC 9.6 CORDLESS BRANCH CUTTER

[. . . ] Page 7 Operation Switching on / off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8 Cutting branches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8 Changing the saw blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8 Maintenance and cleaning Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] A) Q Starting lock W Charging socket E Handle R On / Off switch T Ventilation grate Y Screw U Saw blade I Branch holder O Saw blade cover P Edge guide L Safety Safety instructions specific to the tool J Keep the tool out of the reach of children. Store the tool in a dry, enclosed space, out of the reach of children. J Make sure that the tool is only operated by persons over 16 years of age and in accordance with the operating instructions. 6 GB / IE Safety / Starting operation J To avoid danger to life from electric shock: Before charging, check the tool, the power pack { , the cable } and the plug q. Repair or replacement must only be carried out by the Service Office or an electrical expert. Damaged tools, mains cables or mains plugs pose a danger to life as a result of electric shock. J Maintenance and cleaning must only be carried out when the tool is switched off and the battery charger is disconnected from the mains power. J Never under any circumstances charge the in tegrated rechargeable battery with the battery charger if damaged. J Only use the original battery charger to charge the integrated battery. J Before connecting the battery charger to the mains power, make sure that the mains current is 230 V ~ 0 Hz and is equipped with a 16 A fuse in accordance with requirements. J Make sure that you do not under any circum stances damage any electricity or telecommunication lines when operating the tool. J In the event of damage please contact the Service Office for your country (see "Warranty and Service" booklet). How to avoid injury: Use the following safety gear when operating the tool: Wear safety goggles, worker safety boots and protective gloves. J Keep your hands and feet well away from the J rotating saw blade U. J Only remove workpieces when the saw blade has come to a complete standstill. J Prevent the saw blade U from coming into contact and/or colliding with stones, metal, or similar materials. J Switch the tool off immediately (release the On / Off switch R ): - if you hit any object (e. g. J Only change the saw blade U when it is at a complete standstill and the tool is switched off J Never under any circumstances connect the ca ble } to the tool during cutting operation. Estimate the fall of the cut branch and make sure you keep out of the area of impact. This could cause a build-up of heat generated during operation of the battery charger. Proper procedure and handling: J Do not overload the tool during operation to such an extent that it comes to a standstill. J Never under any circumstances switch the tool on when it is being charged. L Starting operation L Charging the integrated recharge able battery The integrated rechargeable battery must be charged before using the cordless branch cutter for the first time. GB / IE 7 Starting operation / Operation / Maintance and cleaning The LED on the power pack { indicates the status of the tool`s rechargeable battery: 1. [. . . ] j Always charge the integrated rechargeable bat tery completely at the beginning and the end of any lengthy period of non-use (for instance in spring and summer). To guarantee a clean cut, the saw blade cover O has an edge guide P. Always position the cut so that edge guide P is lying on the branch. 8 GB / IE Maintance and cleaning / Disposal / Information L Cleaning L Declaration of conformity j Remove any dirt (e. g. wood shavings / sawdust and plant debris) from the tool using a dry cloth. j Clean the saw blade U thoroughly. We, Kompernaß GmbH, Burgstr. [. . . ]