User manual KOMPERNASS EBENCH KH 2025 DIGITAL WORLD RADIO RECEIVER

[. . . ] Different contries can have deviating legal regulations regarding the freely receivable frequency range. Please note that reception outside of these regulations can therefore be illegal and punishable. Tuning range . . . . . . : USW 50 KHz MW Europe 9 KHz MW USA 10 KHz SW 5 KHz / 1 KHz LW 1 KHz Sensitivity . . . . . . . . . . : SW 2 levels selectable c) Other Memory positions: 160 stations Timer. . . . . . . . . . . . . . . . . . : 2 alarm times 9 min. Sleep timer Output. . . . . . . . . . . . . . . . : Connection for stereo headphones 3. 5 mm Power supply . . . . : Connection for external power supply DC 6 V ­ 7. 5 V Batteries . . . . . . . . . . . . : 4 x 1. 5 V type "AA" 5 KH2025-2026_IB_UK 01. 04. 2004 11:29 Uhr Seite 6 3. Safety Instructions Transportable world receivers are used in a wide range of climate zones. [. . . ] A ferrite antenna is built into the device for medium wave (MW) and long wave (LW) reception. Memory A total of 160 memory positions are available ­ specifically . . . 5 blocks of 10 positions each for USW 5 blocks of 10 positions each for MW 5 blocks of 10 positions each for SW 1 block with 10 positions for LW. The blocks are also designated as "pages". This division into blocks is useful to allow the stations to be saved according to a meaningful organisation principle. by type: music, news, sports by location: local stations or frequently visited travel destinations by person: if multiple family members use the device 10 KH2025-2026_IB_UK 01. 04. 2004 11:29 Uhr Seite 11 a) Saving Stations When you have found a station that you would like to save: » Press the button MEMORY. Two small windows then appear in the display: - PAGE containing the numbers 1. . . 5 - MEM containing an empty field. Make your selection within the next 10 seconds, otherwise this display disappears and you must start this step again. Press the button PAGE until the small window PAGE contains the number for the block 1. . . 5 to which you would like to save the station. Once you have selected the desired block (page), . . . · then press one of the buttons M0/5 M1/6 M2/7 M3/8 M4/9 to select the memory position 0. . . 9. The number associated with the memory position then appears in the small window MEM. Each press switches between the two assignments (e. g between 0 and 5). The station is now saved. 11 KH2025-2026_IB_UK 01. 04. 2004 11:29 Uhr Seite 12 b) Loading Saved Stations If you would like to load a saved station: ² First select the band (reception range). Press the button PAGE until the small window PAGE contains the number for the block 1. . . 5 from which you would like to load the station. · Then press one of the buttons M0/5 M1/6 M2/7 M3/8 M4/9 until the number of the desired memory position appears in the second small window MEM. Each press switches between the two assignments (e. g between 0 and 5). c) Memory Scanning If you have saved multiple stations: First select the band (reception range). · Press the button PAGE until the small window PAGE contains the number for the block 1. . . 5 in which you would like to start the scan. Pressing any button (except for the volume buttons) ends the memory scan. 12 KH2025-2026_IB_UK 01. 04. 2004 11:29 Uhr Seite 13 8. Clock and Timer The device can be used as a radio alarm with two alarm times and one date alarm. a) Setting the Time When the device is switched off, and the date and time appear in the display in alternation: µ Press the button MODE . ´ Press one of the TUNING buttons briefly to set the time by minute. ´ Hold one of the TUNING buttons pressed to change the time in 10-minute steps. b) Setting the Date ¾ Press the button MODE until the date blinks in the display. ´ Press one of the TUNING buttons briefly to set the date by day. [. . . ] - CITY and DATE and : When the device is switched off, the time and date as well as the travel destination time region will be displayed in alternation. 10. Self-Help Do not open the housing of the device ­ there are no operating elements contained inside. Do not use any cleansers or abrasive agents, these could scratch the housing and in particular the display window. b) If Something Does Not Function Remove all batteries for 2-3 minutes and unplug any external power supply connected to the device if it does not react as described in this manual. [. . . ]