User manual KINGSTON SD2 DATASHEET

[. . . ] 11 Document No: 4808037-001. A00 DataTraveler BlackBox ® 2 1 1. 1 · · · · SYSTEM Requirements Pentium III Processor 16MB free disk space USB 1. 1/ 2. 0 Operating Systems o o o Windows 2000®, SP3 and SP4. Windows VistaTM · Two available drive letters between physical drives and network shares. Document No: 4808037-001. A00 DataTraveler BlackBox ® 3 2 2. 1 1. GETTING STARTED Driver Installation Insert the DataTraveler® BlackBox (DTBB) into an available USB port. Select Run DTBB_Launcher. exe to continue. Figure 1: AutoPlay Dialog 2. 2 Initial Setup 1. After the hardware installation is complete, the Setup Wizard will guide you through the initial configuration of DTBB. [. . . ] During your initial configuration of the DTBB, you must set a device password for data protection. This password enables the use of the device as a removable storage, and protects your DTBB application data and file information. After selecting the language and accepting the license agreement, the Password Setup dialog box will be displayed (Figure 3). Figure 3: Complex Password The Password Setup dialog box (Figure 3) requires you to enter a password and re-enter it for confirmation. The password must be a minimum of 6 characters and must not exceed 16 characters. It must also contain three different types of characters: lower case letters, upper case letters, numeric and/or special characters. A password hint is strongly recommended to remind you of your password. (Example of Complex Passwords: ABC$123 or Bob411). Document No: 4808037-001. A00 DataTraveler BlackBox ® 5 4. Enter your Contact Information into the appropriate fields (Figure 4). Figure 4: Contact Information 5. Click Finish to complete the initial setup of DTBB. Document No: 4808037-001. A00 DataTraveler BlackBox ® 6 3 3. 1 USING DTBB Login to DTBB 1. After the initial Setup is complete, you will automatically be logged into DTBB. Hereafter, you will login to DTBB after Windows recognizes the drive is inserted into the USB port. The quickest way for administrative users to solve this problem is to manually change the drive letter of the flash drive via Disk Management. For Kingston DTBB, change the conflicting drive letter for the DTBB Launcher partition. Non-administrative users should reinsert the DTBB, which could result in Windows reassigning a different drive letter for DTBB, or permanently reassign the conflicting network share to a different drive letter. Q3) I inserted the DTBB into a Windows XP system and it does not show up in My Computer or I receive a, "DTBB requires two free drive letters. . . " error message. A3) This is a common Windows XP issue which is caused by a drive letter conflict. In configurations where the network drive letter(s) follow physical drive letters, Windows XP may assign newly inserted flash drives a drive letter which is already taken by a network share. The quickest way for administrative users to solve this problem is to manually change the drive letter of the flash drive in Disk Management, located in Control Panel -> Administrative Tools -> Computer Management. For Kingston DTBB, change the conflicting drive letter for the DTBB Launcher partition. If the launcher does not auto-run reinsert the drive or manually run the Launcher from the DTBB Launcher partition. See Microsoft Knowledge Base article for details at: http://support. microsoft. com/default. aspx?scid=kb;en-us;297694 Note: If the launcher still does not auto-run, you may need to disable or upgrade any third party hard disk encryption software. A4) The new hardware setup in Microsoft Windows XP may not always start the auto-run code on the drive. [. . . ] The DTBB software launcher is located on the DTBB Launcher drive as "DTBB_Launcher. exe. " Document No: 4808037-001. A00 DataTraveler BlackBox ® 11 Note: Make sure the ExmpSrv. exe process is not running in the Task Manager when attempting to launch the DTBB Launcher. On Windows Vista, the AutoPlay process has been changed to better improve system security. Depending on how the system is setup for AutoPlay, the DTBB drive may or may not launch automatically after insertion. By default, the AutoPlay dialog will display after inserting the drive into the USB port. [. . . ]