User manual KAWAI Q-80EX

[. . . ] 3 CONSERVATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SYMBOLS USED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 EQUIPMENT FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] ATTENTION Q-80EX must be installed by qualified personnel and in compliance with regulations, there must be a tap above (to exclude the equipment from the water system in the case of maintenance interventions), a check valve, water supply pipes above and below the equipment and an electrical outlet. Avoid subjecting the machine to excessive temperature changes that could cause condensate to form inside, which can damage the electronic part. Make sure the air vents are never blocked in order to not compromise motor cooling. Instructions and representation to follow are to be considered for typical installations, the specific components may vary depending on the accessories that accompany the car and taps derivation and delivery chosen. CONTROLS TO BE CARRIED OUT BEFORE INSTALLATION Mains grounding present and efficient. Main compatible with the electrical specifications indicated on the plate on the back of the machine. Stability of network tension (rushes lower than 10%). Glass/dish washmachine Easyglass Q-80EX Inlet 3 1 2 4 6 5 Permeate Drain -8- 3. 1 INSTALLING THE DRAIN CLAMP Install the drain clamp on the drain siphon of the sink. Make sure the washer correctly rests on the pipe and the bolts are tightened. It is advisable to sanitize the system every six months during routine maintenance procedures. Contact assistance in order to carry out this operation, which must be performed by specialized personnel/installation technicians. 4. 4 ELECTRONIC BOARD OPERATING 4. 4. 1 Normal functioning KAWAI When the card is in normal functioning mode, the name of the reseller is displayed. When the faucet is opened, the machine starts to produce permeate water; uS/cm 0050 pushing the key ENTER , the conductivity is displayed. - 10 - When the faucet will be closed, the board returns in stand-by mode. Main water pressure failure Alarm P. 5. 3 REPLACING FILTER CARTRIDGE ITEM TO CHECK The repleace the prefilter follow these steps: Remove the power plug. Install new cartridge in the machine; take caref about the filter o-rings. Sterilize the system (see § 5. 8). 5. 4 PRELOAD EXPANSION TANK To check the preload of the pressure tank, follow these steps: Remove the power plug. Empty the expansion tank delivering water to the permeate auxiliary outlet. Turn the machine on its side and identify the attack based on the preloading of the pressure tank. With a compressor and a pneumatic gun, bring the preload pressure at 2. 5bar Return it to the original position the machine and connect the power plug. - 14 - 5. 5 VERIFICATION OF THE SETTING For proper operation of the machine, check periodically the calibrations. 5. 5. 1 Setting pressure switch Install a pressure gauge (0-6 bar or similar) between the permeate outlet and the faucet. Open the knob of the tap, after which it slowly close the tap until the pressure gauge reaches about 3. 5 bar. Slowly unscrew the calibration nut of pressure switch until the operation of the machine becomes discontinuous. Apply the glue sealant to calibration nut. v re o ite g lazio e n p s o tato re s s Calibration nut 5. 5. 2 Check operating pressure Install a T fitting and a pressure gauge 0-10 bar (or similar) on the pump outlet line. The operating pressure must be between 8 and 9 bar. 5. 5. 3 Calibrating conductivity probe Open the electronic board box. [. . . ] Deitar este aparelho em um centro de recolha ou de reciclagem segundo a lei local e nacional. O consumidor tem uma importante responsabilidade na redução do lixo, preparando a reciclagem dos instrumentos eléctrico/electrónicos. A reciclagem previne a dispersão de materiais perigosos nos lixos minicipais. O símbolo da barra no barril lembra ao utilizador de não jogar este producto como um lixo municipal não classificado. [. . . ]