User manual KAWAI MP4

[. . . ] Stage Piano MP4 Owner's Manual Important Safety Instructions SAVE THESE INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. AVIS : RISQUE DE CHOC ELECTRIQUE The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. - NE PAS OUVRIR. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the leterature accompanying the product. Examples of Picture Symbols denotes that care should be taken. The example instructs the user to take care not to allow fingers to be trapped. The example instructs the user to remove the power cord plug from the AC outlet. Read all the instructions before using the product. [. . . ] The following parameters are provided: CUTOFF, ATTACK, DECAY and RELEASE. Make sure that the TONE MODIFY button in the CONTROL KNOBS section is lit. The CONTROL KNOBS are now active and assigned to the Tone Modify parameters for the current sound. Use the CONTROL KNOBS to change the current settings for the selected zone. Each parameter of the TONE MODIFY function has an adjustable range from -50 to +50. 1CUT ATK DCY RLS +50 -20 +40 +10 CUTOFF: ATTACK: DECAY: RELEASE: Raising the CUTOFF level makes the sound brighter, lowering the level makes the sound duller. As the value increases, the attack time becomes longer, which means a slower attack is produced. This parameter controls the amount of time from the peak level to the sustain level of the sound. This parameter controls the amount of time needed for the sound to fade out after the key is released. Volume level Time ATTACK DECAY KEY OFF RELEASE Note: If the selected zone is set to BOTH, changing the TONE MODIFY parameters affects for both internal and external sections. If you want different settings for internal and external sections, enter the edit mode by pressing the MENU button and select internal or external section with ZONE SELECT button. (See page 29 for details. ) 5. 4 MIDI CC# (Control Change) The MP4 can send any MIDI Continuous Controller information to any MIDI Instrument or Device. 25 This powerful feature allows for editing the sounds of an external sound module in Real Time during performance, or for recording Real Time performance edits to a MIDI sequencer. Make sure that the MIDI CC# button in the CONTROL KNOBS section is lit. The CONTROL KNOBS are now active and assigned to the MIDI CC parameters. Use the CONTROL KNOBS to change the MIDI continuous controller information assigned to each knob as described below. Each parameter of the Control Change has an adjustable range from 0 to 127. When the selected zone is set to INT or BOTH, the display shows the parameter names. 1PAN STN VbR VbD 0 0 0 0 When the selected zone is set to EXT, the display shows the MIDI CC numbers. 3010 070 076 077 64 64 64 64 The default parameters assigned for each knob are as follows. A: #10 Panpot (PAN) B: #70 Sustain Level (STN) C: #76 Vibrato Rate (VbR) D: #77 Vibrato Depth (VbD) Note: If the selected zone is set to BOTH, changing the MIDI CC# parameters affects for both internal and external sections. If you want different settings for internal and external sections, enter the edit mode by pressing the MENU button and select internal or external section with ZONE SELECT button. (See page 29 for details. ) Changing MIDI CC parameter Press and hold the MIDI CC# button. The MIDI CC# button starts blinking and the cursor in the display moves up to the parameter name. 1PAN STN VbR VbD 0 0 0 0 Use the CONTROL KNOBS to change the parameters. The MIDI CC# button stops blinking and the cursor in the display moves down to the value. 26 Note: When the selected zone is set to INT, only the following parameters can be selected. 10 11 70 71 76 77 78 93 Panpot Expression Sustain Level Resonance Vibrato Rate Vibrato Depth Vibrato Delay Chorus Depth PAN EXP STN RSN VbR VbD VbY ChD When the selected zone is set to BOTH and the internal section is selected in edit mode, the parameters not available for INT section show as XXX. 1015 STN VbR VbD Ixxx 0 0 0 27 6. MENU The MENU buttons allow access to the edit parameters in the MP4. This collection of settings together with other editable parameters can be stored as a SETUP. [. . . ] If you have an older Macintosh OS, please use an appropriate MIDI interface and MIDI cables when connecting the MP4 to a Macintosh computer. NOTE: When both MIDI jacks and USB jack are connected, USB has priority. When connecting USB cable to the MP4, first connect the USB cable and then turn the power of the MP4 on. It may take some time to start communication when the MP4 is connected to the computer via USB. [. . . ]