User manual KAWAI FS900

[. . . ] If this products leaks when a camera is installed, remove the battery from the camera as quickly as possible. There is the possibility of ignition and explosion from generation of hydrogen gas. If it is broken by severe impact with a rock or other hard object, the broken pieces could cause injury. Do not expose this product to extreme temperatures or extremely variable temperatures. [. . . ] <Examples of foreign matter sticking to the waterproof packing> Hair Fibers Grains of sand 2. The speed at which the waterproof packing deteriorates depends on usage and storage conditions. If the waterproof packing is damaged, shows cracks, or has lost its elasticity, leakage may result. Its water resistant properties may be affected if it is deformed by exposure to high temperatures for a long period (for example, if it is left in an automobile, on a boat, or at the beach), or subjection to uneven external force for a long time. Also, do not place heavy objects on this product during storage or transport. When the surface in contact with the waterproof packing is pressed strongly from the outside of the product, or when the product is twisted, the water resistant function may be lost. Before using this product, perform the preliminary test and the final check. If you notice drops of water or other signs of water leakage while taking pictures, stop shooting immediately, remove any water from the camera and the product, and perform the tests in "Final check" to determine whether leakage has occurred or not. E-5 Handling the Product Do not use or store the unit in places such as listed below: Doing so may cause malfunctions, defects, damage, fire, internal clouding, or water leakage. Areas exposed to strong vibrations Areas exposed to excessive temperatures or humidity. This product is made of polycarbonate resin with high impact resistance, but it could be damaged by scraping against rocks or other hard objects. This product its not designed to absorb impacts and protect the camera inside. · If the preliminary test should show water leakage with normal handling, stop using the case and contact your dealer or nearest Olympus Service Station (listed on the rear page of this instruction manual). E-11 3. Installing the Digital Camera. Check the digital camera. Check the digital camera before installing it in the Case. Battery check As the LCD monitor is used for picture confirmation when taking pictures, the battery tends to be used up quickly. Confirm that the remaining battery capacity is sufficient. Checking the number of pictures remaining to be taken Make sure that the number of remaining pictures available is sufficient. Removing the hand strap from the digital camera If a hand strap is attached to the digital camera, it must be removed. CAUTION : · If a digital camera is loaded without removing the strap, the strap may get caught between the case lids and may cause water leakage. shall not be responsible for damage caused by dropping the camera. Loading the camera in the case Which digital cameras can be loaded? This case (FS900) is exclusively for the µ-mini DIGITAL/Stylus Verve. Turn on the camera. Press the power button on the digital camera once to switch it on. If the camera is not operated for about three minutes, it will enter the sleep mode (standby condition) and stop operation. To return to the active mode, just press any operation button such as the zoom button. If the camera is left untouched for more 12 minutes, it will switch off completely. In this case, switch it on again on by pressing the power switch button. E-12 Check camera operation. Make sure that the camera operates according to the digital camera's instruction manual. Open the water resistant case. While sliding the buckle lock levers on the left grip of the case downward, hold the upper and lower sections of the left grip and pull it toward the front to open the case. Load the digital camera. Carefully place the digital camera in the case. Check the loading status. Always perform the following final checks before sealing the case. Is there any abnormality with the waterproof packing where the case opens?Are the waterproof packing and the waterproof packing contact surface free of dirt and other foreign matter? E-13 Seal the case. Close the rear lid of the case, engage the buckles with the edge of the rear lid, and tilt the left grip in the direction of the arrow to seal the case airtight. Perform the final checks. Always check your pictures on the LCD monitor after shooting. E-16 5. [. . . ] After use in or near sea water, it is important to immerse the case in fresh water long enough to remove any salt. CAUTION : · Water leakage may be caused when the case is exposed to local water pressures above its maximum limit. Before washing the case with fresh water, make sure you have removed the digital camera. · Drying the case while there is still salt on it may cause deterioration. Always wash off any salt after use. Dry the case. After washing with fresh water, use a soft, dry, lint-free cloth to wipe off any water drops, then dry the case completely at a well-ventilated and shady location in the shade. CAUTION : · Do not use hot air from a hair drier or similar device to dry the case. [. . . ]