User manual KAWAI EP308S

[. . . ] WARNING - When using electric products, basic precautions should always be followed, including the following. potential could result in death WARNING Indicates ainjury if thehazard thathandled incorrectly. or serious product is The product should be connected to an AC outlet of the specified voltage. 120V 230V 240V G If you are going to use an AC power cord, make sure that its has the correct plug shape and conforms to the specified power voltage. G Failure to do so may result in fire. Do not insert or disconnect the power cord plug with wet hands. Doing so may cause electric shock. When using the headphones, do not listen for long periods of time at high volume levels. Doing so may result in hearing problems. Do not disassemble, repair or modify the product. Doing so may result in product breakdown, electric shock or short-circuit. 2 When disconnecting the AC power cord's plug, always hold the plug and pull it to remove it. The product is not completely disconnected from the power supply even when the power switch is turned off. [. . . ] Control Knobs Select the function with the buttons on the left and use the knobs to change the values. You can also move the cursor with the MENU buttons and change the value with the VALUE buttons while the display is showing Control Knobs function. 5. 1 EFFECT Make sure that the EFFECT button in the CONTROL KNOBS section is lit. The CONTROL KNOBS are now active and assigned to the EFX/REVERB parameters for the selected zone. Use the CONTROL KNOBS to change the current settings. 1EfR EfD RvT RvD 41 64 96 127 EfR (EFX Rate) adjusts the value of the preset parameter for each EFX. (internal only) EfD (EFX Depth) adjusts the depth of the EFX added to the sound. (internal only) RvD (REVERB Depth) adjusts the depth of the reverb added to the sound. EFX parameter list EFX Rate rate 0 -12. 7Hz rate rate rate delay time delay time delay time delay time rate rate rate rate rate rate rate rate 0 -12. 7Hz 0 -12. 7Hz 0 -12. 7Hz 0 -100 (%) 0 -100 (%) 0 -100 (%) 0 -100 (%) 0 -12. 7Hz 0 -12. 7Hz 0 -12. 7Hz 0 -12. 7Hz 0 -12. 7Hz 0 -12. 7Hz slow/fast slow/fast EFX Depth send level send level send level send level send level send level send level send level wet balance wet balance wet balance wet balance wet balance wet balance wet balance wet balance 1. OVERDRIVE sense sense intensity drive 0 -100 (%) 0 -100 (%) 0 -100 (%) 0 -100 (%) wet balance wet balance send level wet balance REVERB parameter list REVERB Time rev. time 0. 3 - 5. 0S rev. time rev. time rev. time rev. time rev. time rev. time 0. 3 - 5. 0S 0. 3 - 3. 0S 0. 3 - 3. 0S 0. 3 - 3. 0S 0. 3 - 3. 0S 0. 3 - 3. 0S REVERB Depth send level send level send level send level send level send level send level 1. PLATE Note: When EFX/REVERB depth is set to 0 while the EFX/REVERB button is active, the EFX/REVERB button will blink to indicate that the EFX/ REVERB is turned ON but the depth is set to 0. If the selected zone is set to BOTH, changing the value for EFX depth or REVERB depth affects for both internal and external sections. If you want different settings for internal and external sections, first enter the edit mode by pressing the MENU button and press the EFFECT button. (See page 29 for details. ) 5. 2 EQ (EQUALIZER) The EP308S contains a four-band graphic equalizer to shape the overall tone of the sound. 10 11 70 71 76 77 78 93 Panpot Expression Sustain Level Resonance Vibrato Rate Vibrato Depth Vibrato Delay Chorus Depth PAN EXP STN RSN VbR VbD VbY ChD When the selected zone is set to BOTH and the internal section is selected in edit mode, the parameters not available for INT section show as XXX. 1015 STN VbR VbD Ixxx 0 0 0 28 29 6. MENU The MENU buttons allow access to the edit parameters in the EP308S. This collection of settings together with other editable parameters can be stored as a SETUP. Inside each of the four zones, a multitude of features and effects can be programmed and combined together into one exciting SETUP. The menu consists of Internal parameters, External parameters and Common parameters. If a zone is set as Both, both the Internal parameters and External parameters are available for the zone. Use the MENU buttons to scroll through all the different parameters. Zone parameters (Int) Mode Sound Selection Damper Effect (Int Piano only) Zone parameters (Ext) Common parameters Master Volume Expression Pedal CC# Footswitch CC# Temperament Stretch Tuning Mode TX Channel TX PRG # On/Off String Resonance (Int Piano only) PRG # Voicing (Int Piano only) TX Bank On/Off Key Range Hi/Lo Bank Select MSB LSB Velocity Switch On/Off Key Range Hi/Lo Velocity Switch Value Velocity Switch On/Off Velocity Compression Velocity Switch Value Velocity Offset Velocity Compression Zone Transpose Velocity Offset Volume Zone Transpose Pan TX Volume On/Off Fine Tune Volume Damper Pedal On/Off/Hold TX Controller On/Off Footswitch On/Off Pan Expression Pedal On/Off Fine Tune Modulation On/Off Damper Pedal On/Off Bender On/Off Footswitch On/Off Bender Range Expression Pedal On/Off Solo On/Off Modulation On/Off Solo Mode Bender On/Off TX Bender Range On/Off Bender Range Solo On/Off Solo Mode Caution: The edited settings will be erased when the power is turned off, or other sound is recalled. To save these settings, use the STORE procedure to save them as a SETUP. (see p. XX) 30 6. 1 Editing Procedure and Parameters First, press the ZONE SELECT button for the zone to be edited. Next, press the MENU buttons until the parameter you want to edit appears in the DISPLAY. When a zone is set as Both, pressing the ZONE SELECT button again will switch the menu list from Internal to External or vice versa. [. . . ] [For Windows 2000/98SE users] You need to install the designated driver in your computer. Visit the KAWAI web site at http://www. kawai. co. jp/english/Download1. html and download the program. [For Macintosh users] Macintosh OSX automatically recognizes our USB interface. If you have an older Macintosh OS, please use an appropriate MIDI interface and MIDI cables when connecting the EP308S to a Macintosh computer. [. . . ]