User manual KAWAI EP308

[. . . ] WARNING - When using electric products, basic precautions should always be followed, including the following. potential could result in death WARNING Indicates ainjury if thehazard thathandled incorrectly. or serious product is The product should be connected to an AC outlet of the specified voltage. 120V 230V 240V G If you are going to use an AC power cord, make sure that its has the correct plug shape and conforms to the specified power voltage. G Failure to do so may result in fire. Do not insert or disconnect the power cord plug with wet hands. Doing so may cause electric shock. When using the headphones, do not listen for long periods of time at high volume levels. Doing so may result in hearing problems. Do not disassemble, repair or modify the product. Doing so may result in product breakdown, electric shock or short-circuit. 2 When disconnecting the AC power cord's plug, always hold the plug and pull it to remove it. The product is not completely disconnected from the power supply even when the power switch is turned off. [. . . ] Use the CONTROL KNOBS to change the current settings. 1EfR EfD RvT RvD 41 64 96 127 EfR (EFX Rate) adjusts the value of the preset parameter for each EFX. (internal only) EfD (EFX Depth) adjusts the depth of the EFX added to the sound. (internal only) RvD (REVERB Depth) adjusts the depth of the reverb added to the sound. EFX parameter list EFX Rate rate 0 -12. 7Hz rate rate rate delay time delay time delay time delay time rate rate rate rate rate rate rate rate 0 -12. 7Hz 0 -12. 7Hz 0 -12. 7Hz 0 -100 (%) 0 -100 (%) 0 -100 (%) 0 -100 (%) 0 -12. 7Hz 0 -12. 7Hz 0 -12. 7Hz 0 -12. 7Hz 0 -12. 7Hz 0 -12. 7Hz slow/fast slow/fast EFX Depth send level send level send level send level send level send level send level send level wet balance wet balance wet balance wet balance wet balance wet balance wet balance wet balance 1. 9. CHORUS FLANGER CELESTE ENSEMBLE DELAY 1 DELAY 2 DELAY 3 DELAY 4 AUTO PAN 1 10. OVERDRIVE sense sense intensity drive 0 -100 (%) 0 -100 (%) 0 -100 (%) 0 -100 (%) wet balance wet balance send level wet balance REVERB parameter list REVERB Time rev. time 0. 3 - 5. 0S rev. time rev. time rev. time rev. time rev. time rev. time 0. 3 - 5. 0S 0. 3 - 3. 0S 0. 3 - 3. 0S 0. 3 - 3. 0S 0. 3 - 3. 0S 0. 3 - 3. 0S REVERB Depth send level send level send level send level send level send level send level 1. PLATE Note: When EFX/REVERB depth is set to 0 while the EFX/REVERB button is active, the EFX/REVERB button will blink to indicate that the EFX/ REVERB is turned ON but the depth is set to 0. If the selected zone is set to BOTH, changing the value for EFX depth or REVERB depth affects for both internal and external sections. If you want different settings for internal and external sections, first enter the edit mode by pressing the MENU button and press the EFFECT button. (See page 29 for details. ) 5. 2 EQ (EQUALIZER) The EP308 contains a four-band graphic equalizer to shape the overall tone of the sound. However, each SETUP can have its own EQ setting that affects the internal sounds only. A positive (+) value indicates amplification, or a boost of that frequency range. This collection of settings together with other editable parameters can be stored as a SETUP. Inside each of the four zones, a multitude of features and effects can be programmed and combined together into one exciting SETUP. The menu consists of Internal parameters, External parameters and Common parameters. If a zone is set as Both, both the Internal parameters and External parameters are available for the zone. Use the MENU buttons to scroll through all the different parameters. Zone parameters (Int) Mode Sound Selection Pedal Effect (Int Piano only) Voicing (Int Piano only) Key Range Hi/Lo Velocity Switch On/Off Velocity Switch Value Velocity Compression Velocity Offset Zone Transpose Volume Pan Fine Tune Damper Pedal On/Off/Hold Footswitch On/Off Expression Pedal On/Off Modulation On/Off Bender On/Off Bender Range Solo On/Off Solo Mode Zone parameters (Ext) Mode TX Channel TX PRG # On/Off PRG # TX Bank On/Off Bank Select MSB LSB Key Range Hi/Lo Velocity Switch On/Off Velocity Switch Value Velocity Compression Velocity Offset Zone Transpose TX Volume On/Off Volume TX Controller On/Off Pan Fine Tune Damper Pedal On/Off Footswitch On/Off Expression Pedal On/Off Modulation On/Off Bender On/Off TX Bender Range On/Off Bender Range Solo On/Off Solo Mode Common parameters Master Volume Expression Pedal CC# Footswitch CC# Temperament Stretch Tuning Caution: The edited settings will be erased when the power is turned off, or other sound is recalled. To save these settings, use the STORE procedure to save them as a SETUP. (see p. 38) 28 6. 1 Editing Procedure and Parameters First, press the ZONE SELECT button for the zone to be edited. Next, press the MENU buttons until the parameter you want to edit appears in the DISPLAY. When a zone is set as Both, pressing the ZONE SELECT button again will switch the menu list from Internal to External or vice versa. Since each parameter has a different value range, consult the following pages for the details. Repeat this procedure for any other parameters in any of the zones that need to be modified. [. . . ] [For Windows XP/Me users] A standard USB driver is already installed in your computer. [For Windows 2000/98SE users] You need to install the designated driver in your computer. Visit the KAWAI web site at http://www. kawai. co. jp/english/Download1. html and download the program. [For Macintosh users] Macintosh OSX automatically recognizes our USB interface. [. . . ]