User manual KAWAI CP200

[. . . ] KAWAI assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual, including the products and software described in it. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by KAWAI; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. This device may not cause harmful interference, and This device complies with Part 15 of the FCC Rules. [. . . ] Configuration options: [No] [Yes, Next reset] [Yes, Every reset] When Log is Full [Do Nothing] This item allows you to choose options for reactions to a full Smbios Event Log. Configuration options: [Do Nothing] [Erase Immediately] Smbios Event Log Standard Settings Log System Boot Event [Disabled] This item allows you to choose options to enable/disable logging of System boot event. configuration options: [Enabled] [Disabled] MECI [1] This item allows you to set Mutiple Event Count Increment (MECI). The number of occurrences of a duplicate event that must pass before the multiplt-event counter associated with the log entry is updated, specified as a numeric value in the range 1 to 255. The number of minutes which must pass between duplicate log entries which utilize a multiple-event counter. METW [60] KAWAI CP200 4-45 Custom Options Log OEM Codes [Enabled] This item allows you to enable or disable the logging of EFI Status Codes as OEM Codes (if not already converted to legacy). Configuration options: [Disabled] [Enabled] Convert OEM Codes [Disabled] This item allows you to enable or disable the converting of EFI Status Codes to Standard Smbios Types (Not all may be translated). configuration options: [Disabled] [Enabled] 4-46 Chapter 4: BIOS setup 4. 8 Boot menu Exit The Boot menu items allow you to change the system boot options. F1: General Help F2: Previous Values F5: Optimized Defaults F10: Save & Exit ESC: Exit Number of seconds to wait for setup activation key. Setup Prompt Timeout [xx] Use the <+> and <-> keys to adjust the number of seconds to wait for setup activation key. cPU 1/2; TR1 1/2 Temperature [xxxºC/xxxºF] The onboard hardware monitor automatically detects and displays the CPU and motherboard component temperatures. Select Ignore if you do not wish to display the detected temperatures. CPU FAN1/2 Speed; FRNT FAN1­4 Speed; REAR FAN1/2 Speed [xxxx RPM] or [Ignore] / [N/A] The onboard hardware monitor automatically detects and displays the speed of CPU fans, front fans, and rear fan in rotations per minute (RPM). 3VSB Voltage FAN Speed Control [Generic Mode] The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators. This item allows you to configure the KAWAI Smart Fan feature that smartly adjusts the fan speeds for more efficient system operation. configuration options: [Generic Mode] [High Speed Mode] [Full Speed Mode] KAWAI CP200 4-51 4. 10 Security menu The Security menu items allow you to change the system security settings. Main Ai Tweaker Advanced Server Mgmt Event Logs Boot Monitor Security Tool Exit Password Description If ONLY the Administrator's password is set, then this only limits access to Setup and is only asked for when entering Setup If ONLY the User's password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights The password length must br in the following range: Minimum length 3 Maximum length 20 Administrator Password User Password Set Setup Administrator Password · If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC) RAM to clear the BIOS password. The Administrator or User Password items on top of the screen show the default Not Installed. ⷠAdministrator Password If you have set an administrator password, we recommend that you enter the administrator password for accessing the system. [. . . ] Connect two independent auxiliary power sources from the power supply to the two graphics cards separately. If your motherboard has more than two PCIEX16 slots, refer to Chapter 2 in this user manual for the locations of the PCIEX16 slots recommended for multi-graphics card installation. Align and firmly insert the 3-Way SLI bridge connector to the goldfingers on each graphics card. Connect three independent auxiliary power sources from the power supply to the three graphics cards separately. [. . . ]