User manual KAWAI CP170

[. . . ] KAWAI assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual, including the products and software described in it. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by KAWAI; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. A-2 Reference information vi Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. [. . . ] DRAM CTRL REF Voltage on CHA [Auto] Allows you to set the DRAM CTRL REF Voltage on Channel A. DRAM DATA REF Voltage on CHA [Auto] Allows you to set the DRAM DATA REF Voltage on Channel A. DRAM CTRL REF Voltage on CHB [Auto] DRAM DATA REF Voltage on CHB [Auto] Allows you to set the DRAM CTRL REF Voltage on Channel B. DRAM CTRL REF Voltage on CHC [Auto] Allows you to set the DRAM CTRL REF Voltage on Channel C. 4-28 Chapter 4: BIOS setup DRAM DATA REF Voltage on CHC [Auto] Allows you to set the DRAM DATA REF Voltage on Channel C. DRAM CTRL REF Voltage on CHD [Auto] Allows you to set the DRAM CTRL REF Voltage on Channel D. DRAM DATA REF Voltage on CHD [Auto] DRAM Read REF Voltage on CHA [Auto] Allows you to set the DRAM DATA REF Voltage on Channel D. Allows you to set the DRAM Voltage for CPU IMC to reference Reads on Channel A. DRAM Read REF Voltage on CHB [Auto] Allows you to set the DRAM Voltage for CPU IMC to reference Reads on Channel B. DRAM Read REF Voltage on CHC [Auto] Allows you to set the DRAM Voltage for CPU IMC to reference Reads on Channel C. DRAM Read REF Voltage on CHD [Auto] Allows you to set the DRAM Voltage for CPU IMC to reference Reads on Channel D. 5 SATAConfiguration While entering Setup, the BIOS automatically detects the presence of SATA devices. The SATA Port items show Not Present if no SATA device is installed to the corresponding SATA port. F1: General Help F2: Previous Values F3: Shortcut F5: Optimized Defaults F6: KAWAI Ratio Boost F10: Save ESC: Exit F12: Print Screen 4-34 Chapter 4: BIOS setup SATA Mode [AHCI Mode] [Disabled] [IDE Mode] [AHCI Mode] Allows you to set the SATA configuration. Set to [IDE Mode] when you want to use the Serial ATA hard disk drives as Parallel ATA physical storage devices. Hotplug support configurations for SATA are disallowed under this mode. Set to [AHCI Mode] when you want the SATA hard disk drives to use the AHCI (Advanced Host Controller Interface). The AHCI allows the onboard storage driver to enable advanced Serial ATA features that increases storage performance on random workloads by allowing the drive to internally optimize the order of commands. Set to [RAID Mode] when you want to create a RAID configuration from the SATA hard disk drives. When read/write of your hard disk errors occur, this feature allows the hard disk to report warning messages during the POST. Status Check [Enabled] SATA6G_1 (Gray) Hot Plug [Disabled] This item appears only when you set the previous item to [AHCI Mode] and [RAID mode]. SATA6G_2 (Gray) Hot Plug [Disabled] This item appears only when you set the previous item to [AHCI Mode] and [RAID mode]. [. . . ] Realtek HD Audio Manager with DTS UltraPC II for Windows® 7TM / VistaTM Configurationoptiontabs(varywiththeaudiodevicesconnected) Device advanced settings Information button Exit button Minimize button Control settings Set default device buttons Connector settings Analog and digital connector status B. Realtek HD Audio Manager for Windows XP Configuration options Exit button Minimize button Control settings window Information button Refer to the software manual in the support DVD or visit the KAWAI website at www. 4 System Recovery The system Recovery Partition (F9 Recovery) and the Recovery DVD assist you in reinstalling the OS and restoring it to its original working state. Before using the Recovery Partition or the Recovery DVD, copy your data files (such as Outlook PST files) to USB flash drives or to a network drive and make note of any customized configuration settings (such as network settings). [. . . ]