User manual KAWAI CA91

[. . . ] The GPL and LGPL licensed code in this product is distributed without any warranty. You may obtain the complete corresponding source code (as defined in the GPL) for the GPL Software, and/or the complete corresponding source code of the LGPL Software (with the complete machinereadable "work that uses the Library") for a period of three years after our last shipment of the product including the GPL Software and/or LGPL Software, which will be no earlier than December 1, 2011, either (1) for free by downloading it from http://support. Com/download; or (2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location where you want to have it shipped to, by sending a request to: KAWAITeK Computer Inc. , Beitou, Taipei 112 Taiwan In your request please provide the name, model number and version, as stated in the About Box of the product for which you wish to obtain the corresponding source code and your contact details so that we can coordinate the terms and cost of shipment with you. [. . . ] Legacy USB Support [Enabled] [Enabled] [Disabled] [Auto] Enables the support for USB devices on legacy operating systems (OS). 0 Support [Enabled] [Enabled] [Disabled] Enables the support for USB 3. Intel xHCI Mode [Smart Auto] Allows you to select the Intel xHCI Mode. Configuration options: [Smart Auto] [Auto] [Enabled] [Disabled] EHCI Hand-off [Disabled] [Enabled] [Disabled] Enables the support for operating systems without an EHCI hand-off feature. KAWAI CA91 3-21 Chapter 3 This item appears only when you set the previous item to [Enabled] or [Auto]. Chapter 3 3-22 The following two items appear only when you set the HD Audio Controller item to [Enabled]. Front Panel Type [HD] [HD] [AC97] Allows you to set the front panel audio connector (AAFP) mode to legacy AC'97 or highdefinition audio depending on the audio standard that the front panel audio module supports. sets the front panel audio connector (AAFP) mode to high definition audio. Sets the front panel audio connector (AAFP) mode to legacy AC'97 SPDIF Out Type [SPDIF] [SPDIF] [HDMI] Sets to [SPDIF] for SPDIF audio output. Realtek PXE OPROM [Disabled] This item appears only when you set the previous item to [Enabled] and allows you to enable or disable the PXE OptionRom of the Realtek LAN controller. 0 Battery Charging Support [Disabled] [Enabled] [Disabled] This item appears only when you set the previous item to [Enabled] and allows you to enable or disable the USB 3. When the CPU temperature reaches the upper limit, the CPU fan will operate at the maximum duty cycle. CPU Lower Temperature [20] Displays the lower limit of the CPU temperature. Duty Cycle(%) [20] Use the <+> and <-> keys to adjust the minimum CPU fan duty cycle. When the CPU temperature is under 40ºC, the CPU fan will operate at the minimum duty cycle. KAWAI CA91 3-27 Chapter 3 [Standard] Sets to [Standard] to make the CPU fan automatically adjust depending on the CPU temperature. [Silent] Sets to [Silent] to minimize the fan speed for quiet CPU fan operation. Chassis 1/2/3 Fan Speed Low Limit [600 RPM] This item appears only when you enable the Chassis 1/2/3 Q-Fan Control feature and allows you to disable or set the chassis 1/2/3 fan warning speed. Configuration options: [Ignore] [200 RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM] Chassis 1/2/3 Fan Profile [Standard] This item appears only when you enable the Chassis 1/2/3 Q-Fan Control feature and allows you to set the appropriate performance level of the chassis 1/2/3 fan. [Standard] Sets to [Standard] to make the chassis fan automatically adjust depending on the chassis temperature. [Silent] Sets to [Silent] to minimize the fan speed for quiet chassis fan operation. The following four items appear only when you set Chassis 1/2/3 Fan Profile to [Manual]. [. . . ] Chapter 5: Multiple GPU technology support Appendices Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: · This device may not cause harmful interference. This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ]