User manual KAWAI ANYTIME

[. . . ] Operation is subject to the following two conditions: · ⷠThis device must accept any interference received including interference that may cause undesired operation. This device may not cause harmful interference, and This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer's instructions, may cause harmful interference to radio communications. [. . . ] The settings specify how the host computer and the remote computer (which the user is using) will exchange data. [VT-UTF8] Uses UTF8 encoding to map Unicode chars onto 1 or more bytes [ANSI] Extended ASCII char set Bits per second [57600] Selects serial port transmission speed. Configuration options: [9600] [19200] [38400] [57600] [115200] 4-32 Chapter 4: BIOS setup Data Bits [8] Configuration options: [7] [8] Parity [None] A parity bit can be sent with the data bits to detect some transmission errors. [None] None [Even] parity bit is 0 if the num of 1's in the data bits is even [Odd] parity bit is 0 if num of 1's in the data bits is odd [Mark] parity bit is always 1 [Space] parity bit is always 0 Stop Bits [1] Stop bits indicate the end of a serial data packet. Configuration options: [1] [2] Flow Control [Hardware RTS/CTS] Flow control can prevent data loss from buffer overflow. When sending data, if the receiving buffers are full, a "stop" signal can be sent to stop the data flow. Once the buffers are empty, a "start" signal can be sent to re-start the flow. Configuration options: [None] [Hardware RTS/CTS] Recorder Mode [Disabled] With this mode enabled only text will be sent. Configuration options: [80x24] [80x25] COM2 Console Redirection [Enabled] Allows you to enable or disable the console redirection feature. Configuration options: [Disabled] [Enabled] Console Redirection Settings Please refer to the description of the Console Redirection Settings item under COM1 for details. KAWAI Z9PE-D16 Series 4-33 Serial Port for Out-of-Band Management/ Windows Emergency Management Services (EMS) Console Redirection [Disabled] Allows you to enable or disable the console redirection feature. Unspecified option will not modify any BMC network parameters during BIOS phase BMC network configuration DM_KAN1 DM_LAN1 IP Address in BMC: DM_LAN1 Subnet Mask in BMC: DM_LAN1 Gateway Address in BMC : DM_LAN1 MAC Address in BMC: DM_LAN1 Address Source in BMC: Configuration Address source Lan1 Lan1 Lan1 Lan1 Lan1 Lan1 IP Address in BMC: Subnet Mask in BMC: Gateway Address in BMC: MAC Address in BMC: Address Source in BMC: 192. Unspecified option will not modify any BMC network parameters during BIOS phase. Configuration options: [Previous State] [Static Mode] [DHCP Mode] The following items appears only when you set Configuration Address source to [Static Mode]. F1: General Help F2: Previous Values F5: Optimized Defaults F10: Save & Exit ESC: Exit Change this to enable or disable all features of Smbios Event Logging during boot. Smbios Event Log Standard Settings Log System Boot Event [Disabled] MECI 1 METW 60 Custom Option Log OEM Codes [Enabled] Convert OEM Codes [Disabled] Note: All values changed here do not take effect until computer is restarted. All values changed here do not take effect until computer is restarted. Enabling/Disabling Options Smbios Event Log [Enabled] Change this to enable or disable all features of Smbios Event Logging during boot. configuration options: [Disabled] [Enabled] 4-40 Chapter 4: BIOS setup Erasing Settings Erase Event Log [No] Choose options for erasing Smbios Event Log. Configuration options: [No] [Yes, Next reset] [Yes, Every reset] When Log is Full [Do Nothing] Allows you to choose options for reactions to a full Smbios Event Log. Configuration options: [Do Nothing] [Erase Immediately] Smbios Event Log Standard Settings Log System Boot Event [Disabled] Allows you to choose options to enable/disable logging of System boot event. configuration options: [Enabled] [Disabled] MECI [1] Mutiple Event Count Increment (MECI). [. . . ] You need to manually install the Intel® Rapid Storage Technology enterprise 3. The support DVD automatically displays the Drivers menu if Autorun is enabled in your computer. If Autorun is NOT enabled in your computer, browse the contents of the support DVD to locate the file ASSETUP. When the Welcome to the Setup Program appears, click Next to start the installation. [. . . ]