User manual JWIN JX-CD4300D INSTRUCTION MANUAL

[. . . ] Read Instructions - All the safety and operating instructions should be road before the product is operated 2. Retain Instructions - The safety and operating Instructions should be retained for future reference. Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. Follow Instructions - All operating and use instructions should be followed. [. . . ] Object and Liquid Entry - Never push objects of any kind into this product though openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock, Never spill liquid of any kind on the product. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) when the power-supply cord or plug is damaged, b) If liquid has been spilled, or objets to have fallen into the product, c) If the product has been exposed to rain or water, d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product its normal operation. e) If the product has been dropped or damaged in any way, and f) when the product exhibits a distinct change in performance-this indicates a need for service. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristic as the original part. Unauthorized substitutions may result in fire, electric shook, or other hazards. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. FIGURE 1 EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE ANTENNA LEAD IN WERE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRONIC SERVICE EQUIPMENT GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H) GROUNDING CONDUCTORS (NEC SECTION 810-21) 3 78 9 6 3 11 5 1 14 10 4 2 13 12 FM MODE /BEAT CANCEL 20 19 18 17 16 15 22 MONO ST 1 2 21 23 24 25 28 27 26 25 Fig. 1 VOLTAGE 110 120 220 240 110 120 VOLTAGE 220 240 ~ SELECTOR (For dual voltage model only!) ~ ~ SELECTOR ~ Fig. 2 4 Fig. 3c Fig. 4 5 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 6 ENGLISH PRECAUTIONS The apparatus shall not be exposed to dripping or splashing. Do not use where there are extremes of temperature (below 5 C or exceeding 35 C). Because of the CD player's extremely low noise and wide dynamic range, there might be a tendency to set the volume on the amplifier unnecessarily high. Doing so may produce an excessively large output from the amplifier which could damage your speakers. Sudden changes in the ambient temperature may cause condensation to from on the optical lens inside the unit. If this happens, take out the disc, leave the unit for about 1 hour, and then proceed to operate. Do not install this equipment in a confined space, such as a book case or built in cabinet. 3c) POWER SUPPLY AC POWER Before use, be sure the corresponds with you local voltage. Connect one end of the mains lead to the AC INPUT socket and the other end to an AC outlet. Note: The installed batteries are automatically disconnected when the mains lead is connected to the unit. [. . . ] When beat is heard Beat (a high pitched noise) may sometimes be heard during the recording of radio broadcasts. If this occurs, set the BEAT CANCEL switch to the position that reduces the level of the beat noise. Safeguards against accidental erasure To protect side A, break out tab (1). To protect side B, break out tab (2) (Fig. 8). To erase or record a protected cassette, cover the tab openings with adhesive tape (3). Note: The REC button cannot be depressed when using a protected cassette. MAINTENANCE Cleaning the tape heads To ensure continued high performance, use a cleaning tape (available f rom your local audio dealer) to clean the head block of the deck after about every 10 hours of use Cleaning the unit Clean the outside of the unit with a clean soft cloth, mois tened with lukewarm water. [. . . ]