User manual JWIN JX-CD4000

[. . . ] KNOB REMAIN MODE KNOB STAND - BY LED SKIP - / TUNER KNOB VOLUME DOWN VOLUME UP SKIP +/ TUNER KNOB MUTE LED FM MODE TAPE KNOB BAND KNOB TUNER KNOB TIMER KNOB CD KNOB REMOTE SENSOR CD OPEN / CLOSE KNOB CD DOOR LCD DISPLAY CASS. TERMINAL (OPTIONAL) AC MAIN SWITCH DUAL VOLTAGE SWITCH (OPTIONAL) BATTERY BACKUP AC POWER CORD COVER AC POWER CORD Installation * * Terminal for FM antenna the antenna wire supplied with the unit can be connected to this terminal. Speaker connection Connect the speaker to the main unit : Extend the SPEAKER WIRES and connect then to the SPEAKERTERMINALS. Disconnect the speaker from the main unit; Disconnect the SPEAKER WIRES from the SPEAKER TERMINALS. [. . . ] * Use SKIP FORWARD or BACKWARD button to select the first track to be programmed. * When the desired track appears on the display, press MEMORY button again. * Repeat this procedure to select other tracks that you wish to program from the disc into the memory. * In the radio MODE, when frequency is displayed, this key is use for setting of memory writing enable state for 5 second. Playing a program * * * Press PLAY/PAUSE. When all track have been played, the display shows the number of tracks and the playing time of the CD song. Erasing a program A program is erased if you : Press PROGRAM then STOP/CLEAR button in stop mode. Note : In setting a new program, the existing one will be cleared. RANDOM PLAYING (for Remote Handset) * * * * * * * * * Press the RANDOM button once, and the RANDOM^ndicator will light up. Select the FUNCTION switch into RADIO function The display will appear FM waveband Select the desired waveband range with the BAND button. (Either AM or FM) Using TUNING UP/DOWN button to select your desired station. The tuner will automatically for the first station of sufficient signal strength. Press above procedure if you wish to select another station. Listening to radio Automatic tuning UK-5 Amplifier * * * * * Press POWER button to switch the unit on. Required sound source (CD, Radio or Tape) can be selected by sliding the function switch to desired location. Set the tone with built in present equalizer (normal, classic, rock or pop) with the Preset EQ button. (for Remote Control optional) Press POWER button to switch off the unit. LISTENING TO COMPACT DISC (CD) The LCD indicator always shown the tracks of a disc or program which are still to be played. It works in all modes, in stop modes, all tracks of the disc or the program are shown. Loading the disc * * * Press FUNCTION switch to select CD mode. Press PUSH OPEN button to open the CD door, display will show ) 0:0" load the CD with printed side facing up. Close the CD door, the CD-player starts and scans the contents list of CD. After a few seconds, the total playing time and the number of tracks appear on the display. Playing the entire disc * * * * Playback will start by pressing PLAY/PAUSE, the indicator then appears. To stop playback, press STOP. SELECTION A DIFFERENT TRACK DURING PLAY * * Press SKIP FORWARD /BACKWARD button on the unit (or remote), the required track number appears in the display. Press PLAY/PAUSE button to starting playing. Starting again with the track that is currently playing * * Press SKIP BACKWARD once. The track will be started again from the beginning. Repeat play * * * * During play, press REPEAT button on the remote control. [. . . ] Press STOP/EJECT if you want to stop playback the end of the tape. Winding the tape * * * Press F. F to fast-forward the tape. Press REW to fast-rewind the tape Press STOP/EJECT to stop fast-forward or fast-rewind, before the end of the tape. UK-6 SUPER BASS Press SUPER BASS button, SUPER BASS sound is effect. MODE/REMAIN Press MODE button changing the display as shown below. In the radio mode : Frequency display >> Clock display >> Time ON >> Time OFF. In the CD mode : (During play) Playing time display >> Remaining time display >> Clock display >>Time ON >> Time OFF. [. . . ]