User manual JWIN JV-TV5020

[. . . ] TROUBLESHOOTING If the system does not function properly, check following points before contacting the service center. No Problem Possible Solutions Verify power to all pieces of equipment in the system. 1 No Video Verify that the power switches are in the ON position. Verify that the cameras are properly hooked up. 2 Video, But no control Turn the power OFF for 30 seconds and then turn it ON again. 8-CHANNEL QUAD SPLITTER JV-TV5020 USER'S MANUAL USER'S MANUAL V C R MODE : The Screen comes to VCR mode. 20 PAGE FREEZE AB JV-TV5020 AUTO MODE : Displays each channel sequentially. INDEX 19 SECTION 1 1. PURPOSE OF THIS PRODUCT SPECIFICATIONS 1 2 1 5 2 6 3 7 4 8 SECTION 2 Z 3. UP CONNECTIONS INSTALLATION 4-1. [. . . ] (1) This splitter has 2pages (is consists of page A with channel 1~4 and page B with channel 5~8). (2) All buttons have a different function by press button short or long. (3) To go into the ZOOM or MENU or VCR mode, press the corresponding button long. (4) By pressing channel button shortly, channel moves to anther channel where is located in the same place on different page. (5) By pressing Quad button shortly in Quad mode, the screen moves to anther Quad mode on different page. (6) If you press channel button long, the screen became freeze frame. (2Vp-p). Page 4 BUZZER Menu Press the MODE/MENU button again, the following menu screen will be displayed. [ BUZZER ] KEY BUZZER LOSS BUZZER ALARM BUZZER ALARM TIME EXIT : : : : [Y] [Y] OFF OFF - PAGE4 - 8-CHANNEL QUAD SPLITTER 8-CHANNEL QUAD SPLITTER JV-TV5020 USER'S MANUAL USER'S MANUAL Fig. 8 Page 4 Menu JV-TV5020 When it is set to be zero (OFF) the corresponding camera will be skipped in the Automatic sequential switching mode. - Buttons on the Front View 16 Title [ INDIVIDUAL ] Dwell Alm Load 03s 03s 03s 03s 03s OFF OFF OFF OFF 75 75 75 75 POWER button is to turn the system ON or OFF. Buttons CH1(ch5), CH2(ch6), CH3(ch7) and CH4(ch8)are to select a channel. QUAD If press button, conversion and page (Page A, Page B) conversion in Quad screen . MODE button displays the PIP or 2PIP. CH1: C 1 CH2: C 2 CH3: C 3 CH4: C 4 QUAD A: PAGE 1 EXIT - PAGE2 - Fig. Camera Title - Place the green color character to the date digit using the , , and the buttons and press the ENTER button. The first empty box will be flashing Select the position you want to enter the letter or the numeric number using the , buttons. and the buttons is to change the new character. MENU button is to go into the on-screen-display mode. VCR button displays the VCR video input. REAR VIEW Press the ENTER button to return to the Page 2 INDIVIDUAL menu. You can enter up to 8 characters for each camera title. Fig. 2 (CONNECTION LOCATIONS ­ Rear View) - Connections on the Back View CAMERA INPUT (channel 1 to 8) connectors are BNC's for composite video input/output. Set the DWELL TIME Dwell Time is the amount of time that a camera is displayed on the screen when the system is in the Automatic sequential switching mode. The Dwell Time can be adjusted individually for each camera and the quad display from 1 to 30 seconds. 8-CHANNEL QUAD SPLITTER 8-CHANNEL QUAD SPLITTER JV-TV5020 USER'S MANUAL USER'S MANUAL DC IN is input for DC +12V. INSTALLATION Basic System Installation Perform following steps to install your splitter. [. . . ] How to Program the Menus for OSD (On-Screen Display) There are three pages of Menus to display the time, date, and a camera title for each camera, etc. To enter the MENU setup mode, press the MODE/MENU button on the front panel of the monitor until the MENU displays on it (2 seconds). The page 1 GENERAL screen will be displayed with beeping sound, and pressing MODE/MENU button one more time will show the Page 2 INDIVIDUAL screen, then the Page 3, Page 1, Page 2, so on. Press the ENTER button the EXIT location in Menu1 to exit the MENU setup mode. C2 C3 C2 C1 01/01/2002 00:00:00 C1 01/01/2002 00:00:00 C2 QUAD Mode 1 Picture In Picture Mode (1PIP) 2 Picture In Picture Mode (2PIP) Sequence Picture In Picture Mode 8-CHANNEL QUAD SPLITTER 8-CHANNEL QUAD SPLITTER 8 JV-TV5020 USER'S MANUAL USER'S MANUAL C1 01/01/2002 00:00:00 JV-TV5020 C1 01/01/2002 00:00:00 AUTO key CHANNEL key Any Mode Auto Sequence Mode Single Mode Single Mode The following diagram shows the sequence of selected mode when pressing QUAD key and CHANNEL keys. [. . . ]