User manual JWIN JV-TV2040

[. . . ] 4 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Be sure to disconnect the power supply to the television or monitor when connecting the camera. · Do not expose the components of this kit to extreme heat, ultraviolet light, or moisture. · Periodically check the cables to be sure they are properly and securely connected. · Employ only authorized technicians to service this unit. -3- OUT OF THE BOX After unpacking, make sure you have all the items shown below. If any are missing, contact your dealer or retailer. Component 5. 5" black & white monitor Diagram Features · · · · · · High resolution Brightness and contrast controls Two channels (for two cameras) Single camera capability Compatibility with a variety of camera, video and audio outputs Built in two camera auto switch Weather resistant camera with lens cover (and two screws to secure camera placement) · High resolution and sensitivity · Low energy consumption and excellent stabilization · Adjustable lens · Infrared lights that enable clear viewing at night · DIN connector · Built in microphone · High quality cable with DIN connector and sufficient length to facilitate monitoring from a distance. 60' cable with DIN plug AC Adapter/Power Cord · UL listed power supply · 15V 1200mA DC power supply -4- FRONT VIEW Volume Knob Time Selector Knob Power ON/OFF Button Power Indicator Control Panel Open/Close Point (Press here to open) Control Panel Door With the control panel open, the following items are in view: 50/60Hz Switch Function Switch Choose CH1/CH2/Auto Control Panel Open/Close Fastener -5- REAR VIEW AC/DC Power input Video Out Socket Audio Out Socket CH1 V-Hold Control CH2 Contrast Control Brightness Control CAMERA VIEW Infrared Lights Integrated Microphone Infrared Lights Camera Bracket DIN Connector -6- PUTTING IT ALL TOGETHER You will be pleased with the ease of installation of this unit. With just a few quick steps, your unit will be up and running in a very short period of time. 1. Connect one end of the 60' cable to the camera cable and connect the other end to the Channel (CH) port on the back of the monitor as follows: If you are using only 1 camera: connect the 60' cable to the CH1 port on the back of the monitor. If you are using 2 cameras: connect the first 60' cable to the CH1 port on the back of the monitor and then connect the second cable to the CH2 port. Attach one end to the power connector port on the left side of the rear of the monitor. Plug the AC/DC adapter into an electrical outlet. That's all there is to set up!You are now ready to start your unit and adjust the monitor image and sound. -7- BASIC OPERATIONS These simple steps will enable you to get the best quality sound and image on your closed circuit monitor. 1. The power indicator light comes on. Power Indicator Light Power ON/OFF Button 2. [. . . ] Consistent with the input video signal, please change the 50/60 Hz switch (front control panel) to the correct position. ONE CHANNEL INPUT CONNECTION -10- TWO CHANNEL INPUT CONNECTION If you wish to use two cameras and observe both views on one monitor, the following set up will suit your purposes. -11- SET UP FOR VCR CONNECTION You can use a VCR to record the images captured by your CCTV, the following set up will enable you to do this. A/V OUT A/V IN JVTV 2040 VCR A/V OUT A/V IN TV MUST BE IN VCR MODE. [. . . ]