User manual JWIN JT-P870

[. . . ] 6 Speakerphone and Receiver Volume Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Answer (Recording) On / Off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Setting the Remote Security Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Area Code Setting After the Language Setting you will be prompted to enter the area code setting: 1. Press the [UP] and [DOWN] buttons to set the first digit of the area code. Time/Date Setting After the Area Code Setting, you will be prompted to enter the Time/Date Setting. At other times if you need to set the time and date, depress the [TIME] button for 2 seconds to start the time setting procedure, then: 1. After the settings are complete, press the [TIME] button once and the telephone will announce the time. Note: If you don't press any keys within 8 seconds after entering the time setting, the telephone will exit setting mode automatically. LCD Contrast After the Time/Date Setting, you will be prompted to enter the LCD Contrast Setting: 1. Ringer HI / LO / OFF Selection To adjust the volume of your ringer on your phone: 1. Slide the [RINGER] switch to `HI' position or `LO' position according to your preference. Slide the [RINGER] switch to the `OFF' position to turn the ringer off. Tone / Pulse Selection Select the dialing mode that your telephone requires by sliding the [T-P] switch to either: `T' position for tone dialing, or to `P' position for pulse dial. Note: While in pulse dial status, press `' to change to tone dial. Speakerphone and Receiver Volume Adjustment These volume switches are located on the sides of the phone base. The receiver volume is on the left and the speaker volume switch is on the right. - Pick up the receiver and slide the [VOLUME] switch to adjust the receiver volume. Answer (Recording) On / Off Setting - The default Answer (recording) state is `On', Press [ANSWER] once and the telephone will display `Answer Off'. Press [Answer] again; the telephone will display `Answer On'. Note: If you wish to enable incoming callers to leave a message, you must set the ANSWER function to `On'. 12/19/2003 8:34 AM 6 Setting the Remote Security Code The remote security code is initially preset to `000'. Depress the [ANSWER] key for about 2 seconds; the telephone will display `security code'. (If there is no further activity for 8 seconds, the telephone will exit the setting mode automatically. ) OPERATION Make Calls - Lift the receiver or press the [SPEAKER] button. - Input the telephone number by pressing the corresponding digit keys. Receive Calls Lift the receiver or press the [SPEAKER] button to answer an incoming call. Flash Function (With Call Waiting Service from your Telephone Company) - Use the Flash button to pick up a new incoming call (after you hear the call waiting beep). [. . . ] If the user accidentally drops it into water, first unplug it from wall jack, and remove it from water. Please keep the telephone dry and do not use it in a damp place, i. e. , near a bathtub, washbowl, kitchen sink, laundry tub or swimming pool. Unplug the phone from the wall jack before cleaning with damp cloth; please do not use liquid or aerosol cleansers. Do not use the phone to report a gas leak in the gas vicinity (as the phone may cause a spark). [. . . ]