User manual JWIN JG-MRS42

[. . . ] You can find the forms on line at: http://www. fcc. gov/formpage. html, or call 1 -800-4183676. Connect the equipment into an outlet on a circuit different from that to which the receiver is needed. Consult the dealer or an experienced radio/TV technician for help. Table Of Contents FCC WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The RX LED will light up in amber when incoming signal is encoded with CTCSS. Otherwise the RX LED will light up in green. Transmitting a Call 1. Press and hold the push-to-talk button, and speak gently into the microphone about 3 inches away from the radio. Release the push-to-talk button when finished transmission. Turn the radio on 1. The radio will beep and the LCD displays ready saved channel settings. Transmitting a Call Tone 1. Press and hold Call/EMG button till the TX LED lights up in red, and the LCD displays CALL. Press and release Call/EMG button when you are in an emergency situation. You may speak into the radio, or transmit an emergency Call Tone for instant HELP. Press and release the Call/EMG button again to exit. Note: The maximum transmission range will vary depending on terrain and environment. Range will be greater in open fields, while the range is shorter within/around buildings or large structures. Illuminating the Display 1. The LCD is illuminated for 5 seconds unless Lamp button is pressed again. (9) (10) (11) (12) (13) (14) LCD icons (1) (2) (3) (4) (5) (6) (7) Active Channel number Active CTCSS channel number RSSI (Receiving signal strength indicator) Automatic Power saver indicator Roger beep indicator Scanning indicator Transmitter power indicator: Keep transmitter power Hi (High) if receiving party is far beyond 2 miles. U nless otherwise keep it Lo (Low) all the way, or your radio may Figure 3: LCD display & icons VOX (Voice activated transmission) Battery status indicator Keypad lock indicator Keystroke tone indicator Receiving indicator Transmission indicator Special Features Automatic Squelch Your GMRS is equipped with automatic squelch circuitry, which filters out weak transmission and unwanted noise. These signals may be picked up as background static, and are usually caused by terrain conditions, or if you have reached the limit of your range. Automatic Power Saver Monitor This feature turns off the Automatic Squelch feature momentarily. This allows your unit to receive all signals to its maximum range, but it may pick up static signals as well. Keypad Lock This feature locks the channel adjustment buttons on the front of the unit so that the channel does not move accidentally. Press and hold Menu button until SCAN icon appears and channel flashes. The radio stops and waits for signal input when an active channel is detected. Press push-to-talk button to speak to the party at detected channel, or press Scroll button to leave the channel and resume scan. If no such operation is made or signal is no longer active for 5 seconds, the radio automatically resumes scan. Press Call/EMG button to exit scan mode and restore previous setting at any stage of scan operation. The radio goes back to original channel when push-to-talk is pressed while scanning. [. . . ] Send the unit pre-paid to the address below in the original packaging or reasonable substitute to prevent damage. You " Must " include your full name shipping address and telephone number and Merchandise Return Authorization ( MRA ) for our reference. Please include your check or money order in the amount of $ 12. 00, payable to jWIN Electronics Corp. , to cover handling and return shipping charges. jWIN will not be responsible for delays or unprocessed claims resulting from a purchaser's failure to provide any or all of the necessary information. [. . . ]