User manual JRC RADAR 1800

[. . . ] INSTRUCTION MANUAL N 42 31. 000'COG122. 3 T DGPS W 81 49. 000'SOG 25. 5KTS MOB MENU PUSH OPEN PUSH SELECT RANGE C-MAP CARD NAV PUSH EVENT/ENT MODE EBL/VRM PUSH OPEN CENTER BRT/CLR STBY OFF PC I/F PORT TX OFF COLOR LCD RADAR-PLOTTER 800 RADAR1 Color Radar / Plotter RADAR1 800 Color Radar/Plotter Before You Begin Thank you for purchasing our RADAR 1800 Color LCD Radar/Plotter. This unit is a sophisticated and easy to use integrated color radar and color plotter. When the unit is connected to a GPS or Loran navigation system, the color plotter function allows you to continuously display latitude, longitude, scale division and track line of the vessel color. · This unit is a compact LCD radar with a 2 kw transmitter & 6. 5 inch color LCD. [. . . ] Select an item with `>' mark to display the submenu in the next hierarchy. 55 Changing settings: · When settings are specified by numerical values, press the Joystick up or down to change the values. When settings are specified by bar chart or by other items, press the Joystick to the left or right to change the settings. Entering changes: · Push the Joystick to enter the change. If you want to cancel the BRT/CLR change, push BRT/CLR before completing it. BRT/CLR Pressing the MENU again or BRT/CLR closes the menu. BUZZER OFF ON Buzzer ON/OFF · Press , select the "ALARM SETTING>" and push the , the "ALARM SETTING" menu is displayed. Select the "BUZZER" and push the Joystick , the "BUZZER" popup menu is displayed. Change settings to ON/OFF by pressing the Joystick to right or left. MENU Joystick MASTER RESET SELECT YOUR LANGUAGE. ENGLISH FRANCAIS DEUTSCH ITALIANO NORSK ESPANYOL Setting LANGUAGE · When you push STBY/OFF to turn the power on while pushing MOB and MENU at the same time, the MASTER RESET display and you can select your language. Press the Joystick up or down to select a language and push it in to open MASTER RESET type select display. Press the Joystick up or down to select HARD or SOFT and push it in to select OK or CANCEL for the select language and the reset type. Press the Joystick to the left or right to select OK and push it in to excute the MASTER reset. After the MASTER reset is executed, the RADAR 1800 is rebooted automatically. (Refer to "Master Reset and Language Select Operation" p. 110) Section 3 Operation MASTER RESET SELECT RESETTING TYPE. SOFT HARD SOFT: INITIALIZE ALL SETTINGS WITHOUT CLEAR WPT&ROUTE DATA HARD: INITIALIZE ALL SETTINGS WITH CLEAR WPT&ROUTE DATA. MASTER RESET YOUR SELECTS ENGLISH SOFT RESET EXECUTE MASTER RESET. OK CANCEL 56 Radar Operation All radar functions operates only in the RADAR full screen or in the RADAR/CHART screen. If any other screen mode is selected the radar will be put into standby mode. Selecting a RANGE [RADAR full screen mode] · Press RANGE to display two Soft Keys. RANGE RANGE RANGE + RANGE + Decrease the range scale. The maximum range scale is 24nm. Section 3 Operation The range rings are automatically set to correspond with this selection. [RADAR/CHART screen mode] · Press RANGE to display four Soft Keys. ZOOM IN ZOOM IN ZOOM RANGE OUT - RANGE + Magnify the chart. ZOOM OUT Reduce the chart. RANGE RANGE + Decrease the range scale. The maximum range scale is 24 nm. The range rings are automatically set to correspond with this selection. 57 Adjusting Receiver Sensitivity · Press the Jog Dial until GAIN is highlighted in the upper right corner of the display. Rotate the Jog Dial clockwise or counterclockwise, to vary the gain and thus control the strength of echo returns on the radar screen. The proper setting is when the background noise is just visible on the screen. a light speckled effect) Adjusting TUNING This procces is for Manual Tuning mode only. Manual Tuning can be selected by MENU, RADAR SETTING, TUNE ­ Manual or Automatic. · Press the Jog Dial until TUNE is highlighted in the upper right corner of the display. [. . . ] Therefore, to turn ON display unit 2's power, first put display unit 1 into standby, then put display unit 1 into standby status, and then turn ON display unit 2. CAUTION While one display unit is transmitting, and another display unit is turned ON, depending on the settings the power may be turned OFF. In cases like this, be sure that transmission status has changed to standby status, then turn ON the power to the other display unit. Immediately after turning OFF the power to the display unit, and the turning ON the power again, absolutely wait at least five seconds before turning it ON. The machine may not operate normally. Section 6 Inter Switch (option) BZ ALARM Setting Refer to p. 107 129 SECTION 7 After-Sales Service When Asking for Service When you think the RADAR 1800 is not operating normally, consult your dealer, our agent, branch, sales department or subsidiary for advice. Repair during warranty period Should a malfunction occur when the RADAR 1800 has been operated according to descriptions and instructions in the instruction manual, it will be repaired free of charge during the warranty period. [. . . ]