User manual JRC NSVS1107

[. . . ] 2004 JRC SAW FILTER NSVS1107 Application 449. 7MHz Low Power Transceiver Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig. 1. Input and Output Impedance 50 Nominal Center Frequency (f0) 449. 7MHz Insertion Loss 449. 2~450. 2MHz 3. 5dB max. [. . . ] 5 3) [ 4 x] Fig. 2 Package dimensions (in mm) 3. 8 0. 93 2. 2 1. 15 3. 8 0. 6 1. 15 0. 93 Fig. 3 Desirable land area (in mm) NSVS1107 Nov. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -10ºC or more than +60ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max. , the time of soldering: 10 seconds max. , the power of soldering iron: 30W max. . Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. This specification specifies the quality of this component as a single unit. [. . . ] 2004 IN 50 O *27nH 11 10 , X , W , U , V OUT 50 O 39pF 12 SAW , P , Q , , T R *27nH , S 33pF 0 S21 FREQUENCY CHARACTERISTICS *murata LQW18A series 0 Insertion Loss [dB] 20 2 (1) 13. 30±0. 20 40 (a) (b) (C) (1. 26±0. 13) (2) 4 60 6 80 100 CH1 : center 449. 7 span 100 CH2 : center 449. 7 span 100 J4Y1 VS971 6. 5±0. 20 8 10 S11 (3) S22 (R0. 3) [4×] Marking (1) Manufacture's Mark (2) Lot Number (a) Year 2. 0 max. (b) Month *Oct. --- X Nov. --- Y Dec. --- Z (0. 76) VSWR S11 11 9 7 5 3 1 399. 7 (2. 54) S22 (2. 54) 11 9 (c) Date 1 --- 0 -9 10 -19 --- 1 20 -31 --- 2 (3) Part Number Mark VSWR 7 5 3 (2. 54±0. 15) 499. 7 Frequency [MHz] (1. 4) [12×] Frequency [MHz] Pin No. Connection 499. 7 1 399. 7 1 2 3 4 5 6 (0. 8) 0 [12 ×] S21 12 1 2 3 4 5 GND(PKG) GND(PKG) OUT/IN GND(signal) GND(PKG) GND(PKG) GND(PKG) GND(PKG) IN/OUT GND(signal) InsertionLoss [dB] 20 40 60 80 100 0. 3 (2. 54±0. 15) 7 8 11 10 9 8 7 6 9 10 11 12 (R0. 3) [12×] 3000 Fig. 2 Package dimensions(in mm) Frequency [MHz] Insertion Loss [dB] GND(PKG) GND(PKG) Fig. 1 Measuring circuit [. . . ]