User manual INTEL I865PE

[. . . ] User's Manual Intel i865PE mainboard for Intel Socket 775 processor TRADEMARK All products and company names are trademarks or registered trademarks of their respective holders. These specifications are subject to change without notice. 60000025PDA10 Manual Revision 1. 0 October 15, 2004 DISCLAIMER OF WARRANTIES: THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THE MANUFACTURER LIMITED WARRANTY. THE MANUFACTURER EXPRESSLY EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING ITS PRODUCTS; INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT. THIS DISCLAIMER OF WARRANTIES SHALL APPLY TO THE EXTENT ALLOWED UNDER LOCAL LAWS IN THE COUNTRY PURCHASED IN WHICH LOCAL LAWS DO NOT ALLOW OR LIMIT THE EXCLUSION OF THE IMPLIED WARRANTIES. ii 80 Port Frequently Asked Questions Below is a list of some basic POST Codes, possible problems, and solutions. [. . . ] Options: 2, 3, 4. Aggressive Memory Mode (AMM) Aggressive Memory Mode reduces delays within the chipset to improve DDR DRAM usage efficiency. Performance upgrade using AMM will largely depend on hardware availability within the chipset. CPU Bus Park Options: Auto, Disabled, Enabled. Intel Fast CS Options: Auto, Disabled, Enabled. Page 4-6 BIOS Intel CPC Function Options: Auto, Disabled, Enabled. System BIOS Cacheable This item allows the system BIOS to be cached in memory for faster execution. Options: Disabled, Enabled. Video BIOS Cacheable This item allows the video BIOS to be cached in memory for faster execution. Options: Disabled, Enabled. AGP Aperture Size (MB) This item defines the size of the aperture if you use an AGP graphics adapter. It refers to a section of the PCI memory address range used for graphics memory. Options: 4, 8, 16, 32, 64, 128, 256 MB. Init Display First This item is used to select whether to initialize the AGP or PCI first when the system boots. Options: PCI Slot, AGP. Page 4-7 BIOS 4-4 Integrated Peripherals Figure 5: Integrated Peripherals RealTek Lan Boot ROM Enable/disable the onboard LAN Boot ROM. OnChip IDE Device Scroll to OnChip IDE Device and press <Enter>. The following screen appears: Page 4-8 BIOS IDE HDD Block Mode IDE Block Mode allows the controller to access blocks of sectors rather than a single sector at a time. Options: Enabled, Disabled. IDE DMA transfer access Automatic data transfer between system memory and IDE device with minimum CPU intervention. Options: Enabled, Disabled. On-Chip Primary (Secondary) PCI IDE The mainboard supports two channel of ordinary IDE interface. Select "Enabled" to activate each channel separately. Note: If you do not use the onboard IDE connector, set the Onboard Primary (Secondary) PCI IDE to "Disabled". IDE Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. In Auto mode, the system automatically determines the best mode for each device. Options: Auto, Mode 0 ~ 4. IDE Primary/Secondary Master/Slave UDMA Select the mode of operation for the IDE drive. Ultra DMA-33/66/100 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver. If your hard drive and your system software both support Ultra DMA-33/66/100, select Auto to enable UDMA mode by BIOS. Options: Auto, Disabled. *** On-Chip Serial ATA Setting *** SATA Mode This option is not selectable. On-Chip Serial ATA Assigning "Primary" will make Serial ATA IDE the Primary port and in effect disable the Parallel-ATA Primary port. Similarly, assigning "Secondary" will disable the Parallel-ATA Secondary port. Enhanced mode allows Serial ATA to work simultaneously with Parallel -ATA. Options: Enhanced Mode, Disabled, For Primary, For Secondary. Page 4-9 BIOS Serial ATA Port 0 /1 Mode Display Serial ATA Port 0/1 assignment to IDE device. The following screen shows On-chip Serial ATA assigned to "For Primary". Display only <Compatible Mode> The following screen shows On-chip Serial ATA assigned to "For Secondary". Display only <Compatible Mode> Page 4-10 BIOS The following screen shows On-chip Serial ATA assigned to "Enhanced Mode". Note: Enhanced mode is available only for Windows2000 and XP. Display only <IDE Enhance Mode> Onboard Device Setup Scroll to Onboard Device Setup and press <Enter>. The following screen appears: USB Controller Enables the USB controller. [. . . ] Reserved Test F000h segment shadow to see whether it is R/W-able or not. Reserved Auto detect flash type to load appropriate flash R/W codes into the run time area in F000 for ESCD & DMI support. Reserved Use walking 1's algorithm to check out interface in CMOS circuitry. Reserved C1h C3h C5h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0B-0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h C-1 Appendix 18h 19-1Ah 1Bh 1Ch 1Dh 1Eh 1Fh 20h 21h 22h 23h Detect CPU information including brand, SMI type (Cyrix or Intel) and CPU level (586 or 686). [. . . ]