User manual INTEL DESKTOP BOARD DH67VR

[. . . ] Intel may make changes to specifications and product descriptions at any time, without notice. Intel Desktop Board DZ68ZV may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be obtained from Intel Corporation by going to the World Wide Web site at: http://www. intel. com/ or by calling 1-800-548-4725. Intel, Intel Core, and Xeon are trademarks of Intel Corporation in the United States and/or other countries. * Other names and brands may be claimed as the property of others. Copyright 2011, Intel Corporation. All rights reserved. Preface This Product Guide gives information about board layout, component installation, BIOS update, and regulatory requirements for Intel Desktop Board DZ68ZV. Intended Audience The Product Guide is intended for technically qualified personnel. [. . . ] Connecting the Serial ATA Cables 48 Installing and Replacing Desktop Board Components Connecting to the Internal Headers Before connecting cables to any of the internal headers, observe the precautions in ?Before You Begin?Figure 24 shows the location of the internal headers and connectors on Intel Desktop Board DZ68ZV. Figure 24. Internal Headers 49 Intel Desktop Board DZ68ZV Product Guide S/PDIF Header Figure 24, A shows the location of the S/PDIF output header. Table 6 shows the pin assignments and signal names for the S/PDIF connector. S/PDIF Header Signal Names Pin 1 2 3 4 Description Ground S/PDIF Out Key (no pin) +5 VDC IEEE 1394a Header Figure 24, B shows the location of the IEEE 1394a header. Table 7 shows the pin assignments and signal names for the IEEE 1394a header. IEEE 1394a Header Signal Names Pin 1 3 5 7 9 Signal Name TPA1+ Ground TPA2+ +12 V Key (no pin) Pin 2 4 6 8 10 Signal Name TPA1Ground TPA2+12 V Ground Front Panel Intel HD Audio Header Figure 24, C shows the location of the front panel Intel HD Audio header. Table 8 shows the pin assignments and signal names for the front panel Intel HD Audio header. Front Panel Intel HD Audio Header Signal Names Pin 1 3 5 7 9 Signal Name PORT 1L PORT 1R PORT 2R SENSE_SEND PORT 2L Pin 2 4 6 8 10 Signal Name GND PRESENCE# SENSE1_RETURN KEY (no pin) SENSE2_RETURN 50 Installing and Replacing Desktop Board Components Alternate Front Panel Power LED Header Figure 24, D shows the location of the alternate front panel power LED header. Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel header. If your chassis has a three-pin power LED cable, connect it to this header. Poor audio quality may occur if passive (non-amplified) speakers are connected to this output. 54 Installing and Replacing Desktop Board Components Connecting Chassis Fan and Power Supply Cables Connecting Chassis Fan Cables Connect chassis fan cables to the chassis fan headers on the Desktop Board. Figure 26 shows the location of the chassis fan headers. Figure 26. Location of the Chassis Fan Headers 55 Intel Desktop Board DZ68ZV Product Guide Connecting Power Supply Cables Figure 27 shows the location of the power connectors. CAUTION Failure to use an appropriate power supply and/or not connecting the 12 V (Figure 27, A) power connector to the Desktop Board may result in damage to the board or the system may not function properly. The 2 x 12 pin main power connector (Figure 27, C) is backwards compatible with ATX12V power supplies with 2 x 10 connectors. Figure 27. Connect the 12 V processor core voltage power supply cable to the 2 x 4 pin connector (Figure 27, A). Connect the main power supply cable to the 2 x 12 pin connector (Figure 27, C). 56 Installing and Replacing Desktop Board Components Setting the BIOS Configuration Jumper NOTE Always turn off the power and unplug the power cord from the computer before moving the jumper. Moving the jumper with the power on may result in unreliable computer operation. Figure 28 shows the location of the Desktop Board?s BIOS configuration jumper block. Figure 28. Location of the BIOS Configuration Jumper Block The three-pin BIOS jumper block enables board configuration to be done in the BIOS Setup program. Table 15 shows the jumper settings for the BIOS Setup program modes. 57 Intel Desktop Board DZ68ZV Product Guide Table 15. Jumper Settings for the BIOS Setup Program Modes Jumper Setting Mode Normal (default) (1-2) Description The BIOS uses the current configuration and passwords for booting. Configure (2-3) After the Power-On Self-Test (POST) runs, the BIOS displays the Maintenance Menu. [. . . ] Pay close attention to the following when reading the installation instructions for the host chassis, power supply, and other modules: ?Product certifications or lack of certifications External I/O cable shielding and filtering Mounting, grounding, and bonding requirements Keying connectors when mating the wrong connectors could be hazardous If the power supply and other modules or peripherals, as applicable, are not Class B EMC compliant before integration, then EMC testing may be required on a representative sample of the newly completed computer. 89 Intel Desktop Board DZ68ZV Product Guide Product Certifications Board-Level Certifications Intel Desktop Board DZ68ZV has the regulatory compliance marks shown in Table 22. Regulatory Compliance Marks Description UL joint US/Canada Recognized Component mark. Declaring compliance to European Union (EU) EMC directive, Low Voltage directive, and RoHS directive. Australian Communications Authority (ACA) and New Zealand Radio Spectrum Management (NZ RSM) C-tick mark. [. . . ]