User manual INTEL DESKTOP BOARD DH61ZE

[. . . ] Intel Desktop Board DH61ZE Product Guide Order Number: G45215-003 Revision History Revision -001 -002 -003 Revision History First release of the Intel Desktop Board DH61ZE Product Guide Second release of the Intel Desktop Board DH61ZE Product Guide Third release of the Intel Desktop Board DH61ZE Product Guide Date October 2011 November 2011 November 2011 Disclaimer INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL?S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, or life sustaining applications. [. . . ] Removing a PCI Express x16 Graphics Card 41 Intel Desktop Board DH61ZE Product Guide Connecting Serial ATA (SATA) Cables SATA cables support the Serial ATA protocol. Each cable can be used to connect one internal SATA drive to the Desktop Board. Attach one end of the SATA cable to one of the SATA connectors on the board (Figure 18, A) and attach the other end of the cable to the SATA drive (Figure 18, B). Figure 18. Connecting a Serial ATA Cable 42 Installing and Replacing Desktop Board Components Connecting to the Internal Headers Before connecting cables to any of the internal headers, observe the precautions in ?Before You Begin?Figure 19 shows the location of the internal headers and connectors on Intel Desktop Board DH61ZE. Figure 19. Internal Headers 43 Intel Desktop Board DH61ZE Product Guide Front Panel Audio Header The front panel audio header shown in Figure 19, A supports both Intel High Definition Audio and AC ?97 Audio. Table 4 shows the pin assignments and signal names for HD Audio and Table 5 shows the pin assignments and signal names for AC ?97 Audio. Front Panel Audio Signal Names for Intel HD Audio Pin 1 3 5 7 9 Signal Name PORT 1L (Microphone) PORT 1R (Microphone) PORT 2R (Headphone) SENSE_SEND PORT 2L (Headphone) Pin 2 4 6 8 10 Signal Name Ground PRESENCE# SENSE1_RETURN KEY (no pin) SENSE2_RETURN Table 5. Front Panel Audio Header Signal Names for AC ?97 Audio Pin 1 3 5 7 9 Signal Name MIC MIC_BIAS FP_OUT_R No connection FP_OUT_L Pin 2 4 6 8 10 Signal Name AUD_GND PRESENCE# AUD_GND KEY (no pin) AUD_GND S/PDIF Header Figure 19, B shows the location of the S/PDIF output header. Table 6 shows the pin assignments and signal names for the S/PDIF output header. S/PDIF Header Signal Names Pin 1 2 3 4 Description Ground S/PDIF Out Key (no pin) +5 VDC 44 Installing and Replacing Desktop Board Components Chassis Intrusion Header Figure 19, C shows the location of the chassis intrusion header. This header can be connected to a mechanical switch on the chassis to detect if the chassis cover is removed. This switch should be in the open position when the chassis cover is installed and closed when the cover is removed. Table 7 shows the pin assignments and signal names for the chassis intrusion header. Chassis Intrusion Header Signal Names Pin 1 2 Description Intruder# Ground TPM Header The TPM header is shown in Figure 19, D. TPM Header Signal Names Pin 1 3 5 7 9 11 13 15 17 19 Signal Name CK_33M_TPM_DIP LFRAME# PLTRST# LAD3 +3. 3 V LAD0 No connection +3. 3 VSB Ground LPCPD# Pin 2 4 6 8 10 12 14 16 18 20 Signal Name Ground Key (no pin) No connection LAD2 LAD1 Ground No connection TPM_SERRQ TPM_CLKRUN# No connection 45 Intel Desktop Board DH61ZE Product Guide Front Panel Header Figure 19, E shows the location of the front panel header. Table 9 shows the pin assignments and signal names for the front panel header. Front Panel Header Signal Names Pin 1 3 5 7 9 Description In/Out Pin 2 4 6 In Power Power Out 10 No pin 8 Description Power LED Front panel LED+ Front panel LEDOn/Off Switch Power switch Ground Not Connected In Out Out In/Out Hard Disk Drive Activity LED Hard disk LED pull-up to +5 V Out Hard disk active LED Reset Switch Ground Reset switch Out NOTE When connecting individual wires from your chassis front panel to the front panel header, be sure to observe the connection polarity. Positive wires are usually solid color and negative wires are usually white or striped. Alternate Front Panel Power LED Header Figure 19, F shows the location of the alternate front panel power LED header. Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel header. If your chassis has a three-pin power LED cable, connect it to this header. Table 10 shows the pin assignments for the alternate front panel header. [. . . ] Install and use the equipment according to the instruction manual. 74 Regulatory Compliance Korea Class B Statement Korea Class B Statement translation: This equipment is for home use, and has acquired electromagnetic conformity registration, so it can be used not only in residential areas, but also other areas. Ensure Electromagnetic Compatibility (EMC) Compliance Before computer integration, make sure that the power supply and other modules or peripherals, as applicable, have passed Class B EMC testing and are marked accordingly. Pay close attention to the following when reading the installation instructions for the host chassis, power supply, and other modules: ?Product certifications or lack of certifications External I/O cable shielding and filtering Mounting, grounding, and bonding requirements Keying connectors when mating the wrong connectors could be hazardous If the power supply and other modules or peripherals, as applicable, are not Class B EMC compliant before integration, then EMC testing may be required on a representative sample of the newly completed computer. 75 Intel Desktop Board DH61ZE Product Guide Product Certifications Board-Level Certifications Intel Desktop Board DH61ZE has the regulatory compliance marks shown in Table 20. Regulatory Compliance Marks Description UL joint US/Canada Recognized Component mark. [. . . ]