User manual INTEL DESKTOP BOARD DH61BE

[. . . ] Intel Desktop Board DH61BE Product Guide Order Number: G23552-002 Revision History Revision -001 -002 Revision History First release of the Intel Desktop Board DH61BE Product Guide Second release of the Intel Desktop Board DH61BE Product Guide Date January 2011 April 2011 Disclaimer INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL?S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, or life sustaining applications. [. . . ] Disconnect the monitor cable from the graphics card back panel connector. Remove the screw (Figure 17, A) that secures the card?s metal bracket to the chassis back panel. Push the card ejector lever down using the tip of a pencil or similar tool (Figure 17, B) in the notch. Removing a PCI Express x16 Graphics Card 43 Intel Desktop Board DH61BE Product Guide Connecting Serial ATA (SATA) Cables SATA cables support the Serial ATA protocol. Each cable can be used to connect one internal SATA drive to the Desktop Board. Attach one end of the SATA cable to one of the SATA connectors on the board (Figure 18, A) and attach the other end of the cable to the SATA drive (Figure 18, B). Figure 18. Connecting a Serial ATA Cable 44 Installing and Replacing Desktop Board Components Connecting to the Internal Headers Before connecting cables to any of the internal headers, observe the precautions in ?Before You Begin?Figure 19 shows the location of the internal headers and connectors on Intel Desktop Board DH61BE. Figure 19. Internal Headers 45 Intel Desktop Board DH61BE Product Guide Front Panel Audio Header The front panel audio header shown in Figure 19, A supports both Intel High Definition Audio and AC ?97 Audio. Table 4 shows the pin assignments and signal names for HD Audio and Table 5 shows the pin assignments and signal names for AC ?97 Audio. Front Panel Audio Signal Names for Intel HD Audio Pin 1 3 5 7 9 Signal Name PORT 1L (Microphone) PORT 1R (Microphone) PORT 2R (Headphone) SENSE_SEND PORT 2L (Headphone) Pin 2 4 6 8 10 Signal Name Ground PRESENCE# SENSE1_RETURN KEY (no pin) SENSE2_RETURN Table 5. Front Panel Audio Header Signal Names for AC ?97 Audio Pin 1 3 5 7 9 Signal Name MIC MIC_BIAS FP_OUT_R No connection FP_OUT_L Pin 2 4 6 8 10 Signal Name AUD_GND PRESENCE# AUD_GND KEY (no pin) AUD_GND S/PDIF Header Figure 19, B shows the location of the S/PDIF output header. Table 6 shows the pin assignments and signal names for the S/PDIF output header. S/PDIF Header Signal Names Pin 1 2 3 4 Description Ground S/PDIF Out Key (no pin) +5 VDC 46 Installing and Replacing Desktop Board Components Front Panel USB 2. 0 Headers Figure 19, C and I show the location of the front panel USB 2. 0 headers and Table 7 shows the pin assignments and signal names. Front Panel USB 2. 0 Headers Signal Names Pin 1 3 5 7 9 Signal Name Power (+5 V) DD+ Ground Key Pin 2 4 6 8 10 Signal Name Power (+5 V) DD+ Ground No Connection NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded cable that meets the requirements for a full-speed USB device. Chassis Intrusion Header Figure 19, D shows the location of the chassis intrusion header. This header can be connected to a mechanical switch on the chassis to detect if the chassis cover is removed. This switch should be in the open position when the chassis cover is installed and closed when the cover is removed. Table 8 shows the pin assignments and signal names for the chassis intrusion header. Chassis Intrusion Header Signal Names Pin 1 2 Description Intruder# Ground 47 Intel Desktop Board DH61BE Product Guide TPM Header The TPM header is shown in Figure 19, E. TPM Header Signal Names Pin 1 3 5 7 9 11 13 15 17 19 Signal Name CK_33M_TPM_DIP LFRAME# PLTRST# LAD3 +3. 3 V LAD0 No connection +3. 3 VSB Ground LPCPD# Pin 2 4 6 8 10 12 14 16 18 20 Signal Name Ground Key (no pin) No connection LAD2 LAD1 Ground No connection TPM_SERRQ TPM_CLKRUN# No connection Front Panel Header Figure 19, F shows the location of the front panel header. Table 10 shows the pin assignments and signal names for the front panel header. [. . . ] Install and use the equipment according to the instruction manual. 76 Regulatory Compliance Korea Class B Statement Korea Class B Statement translation: This equipment is for home use, and has acquired electromagnetic conformity registration, so it can be used not only in residential areas, but also other areas. Ensure Electromagnetic Compatibility (EMC) Compliance Before computer integration, make sure that the power supply and other modules or peripherals, as applicable, have passed Class B EMC testing and are marked accordingly. Pay close attention to the following when reading the installation instructions for the host chassis, power supply, and other modules: ?Product certifications or lack of certifications External I/O cable shielding and filtering Mounting, grounding, and bonding requirements Keying connectors when mating the wrong connectors could be hazardous If the power supply and other modules or peripherals, as applicable, are not Class B EMC compliant before integration, then EMC testing may be required on a representative sample of the newly completed computer. 77 Intel Desktop Board DH61BE Product Guide Product Certifications Board-Level Certifications Intel Desktop Board DH61BE has the regulatory compliance marks shown in Table 20. Regulatory Compliance Marks Description UL joint US/Canada Recognized Component mark. [. . . ]