User manual INTEL DESKTOP BOARD DH55TC

[. . . ] Intel Desktop Board DH55TC Product Guide Order Number: E78882-001 Revision History Revision -001 Revision History First release of the Intel Desktop Board DH55TC Product Guide Date October 2009 If an FCC declaration of conformity marking is present on the board, the following statement applies: FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions related to the EMC performance of this product, contact: Intel Corporation, 5200 N. E. Elam Young Parkway, Hillsboro, OR 97124 1-800-628-8686 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Connect a monitor to the graphics card according to the manufacturer?s instructions. Figure 19. Installing a PCI Express x16 Graphics Card Removing a PCI Express x16 Graphics Card Follow these instructions to remove a PCI Express x16 graphics card from a connector: 1. Disconnect the monitor cable from the graphics card back panel connector. Remove the screw (Figure 20, A) that secures the card?s metal bracket to the chassis back panel. Push the card ejector lever down using the tip of a pencil or similar tool (Figure 20, B) in the notch. Pull the card straight up to remove it. 42 Installing and Replacing Desktop Board Components Figure 20. Removing a PCI Express x16 Graphics Card 43 Intel Desktop Board DH55TC Product Guide Connecting Serial ATA (SATA) Cables SATA cables support the Serial ATA protocol. Each cable can be used to connect one internal SATA drive to the Desktop Board. Attach one end of the SATA cable to one of the SATA connectors on the board (Figure 21, A) and attach the other end of the cable to the SATA drive (Figure 21, B). Figure 21. Connecting a Serial ATA Cable 44 Installing and Replacing Desktop Board Components Installing an Intel Z-U130 USB Solid-State Drive (or Compatible Device) An Intel Z-U130 USB Solid-State Drive (or compatible device) can be installed on the Desktop Board by using the onboard USB 2. 0 header indicated in Figure 1, T. To install an Intel Z-U130 USB Solid-State Drive (or compatible device) on the Desktop Board, follow these steps: 1. Align the connector (Figure 22, A) on the bottom of the solid state drive with the USB 2. 0 header on the Desktop Board. The connectors are keyed and will mate correctly when the solid state drive is oriented as shown in Figure 22. Secure the solid state drive to the Desktop Board with the screw (Figure 22, B) included with the board. Figure 22. Installing an Intel Z-U130 USB Solid-State Drive (or Compatible Device) If not used with an Intel Z-U130 USB Solid-State Drive (or Compatible Device), this USB header can be used as an additional dual-port front panel USB header. 45 Intel Desktop Board DH55TC Product Guide Connecting to the Internal Headers Before connecting cables to any of the internal headers, observe the precautions in ?Before You Begin?Figure 23 shows the location of the internal headers and connectors on Intel Desktop Board DH55TC. Figure 23. Internal Headers 46 Installing and Replacing Desktop Board Components Front Panel Audio Header The front panel audio header shown in Figure 23, A supports both Intel High Definition (HD) Audio and AC ?97 Audio. Table 4 shows the pin assignments and signal names for HD Audio and Table 5 shows the pin assignments and signal names for AC ?97 Audio. Front Panel Audio Signal Names for Intel HD Audio Pin 1 3 5 7 9 Signal Name PORT 1L (Microphone) PORT 1R (Microphone) PORT 2R (Headphone) SENSE_SEND PORT 2L (Headphone) Pin 2 4 6 8 10 Signal Name GND PRESENCE# SENSE1_RETURN KEY (no pin) SENSE2_RETURN Table 5. Front Panel Audio Header Signal Names for AC ?97 Audio Pin 1 3 5 7 9 Signal Name MIC MIC_BIAS FP_OUT_R AUD_5V FP_OUT_L Pin 2 4 6 8 10 Signal Name AUD_GND AUD_GND FP_RETURN_R KEY (no pin) FP_RETURN_L Internal Mono Speaker Header The internal mono speaker header is shown in Figure 23, B. Table 6 shows the pin assignments and signal names for the internal mono speaker header. + 47 Intel Desktop Board DH55TC Product Guide S/PDIF Header Figure 23, C shows the location of the S/PDIF output header. [. . . ] EMC Regulations Regulation (Class B) FCC 47 CFR Part 15, Subpart B ICES-003 Issue 4 EN55022:2006 Title Title 47 of the Code of Federal Regulations, Part 15, Subpart B, Radio Frequency Devices. (Canada) Limits and methods of measurement of Radio Interference Characteristics of Information Technology Equipment. (European Union) Australian Communications Authority, Standard for Electromagnetic Compatibility. (Australia and New Zealand) Limits and methods of measurement of Radio Disturbance Characteristics of Information Technology Equipment. [. . . ]