User manual INTEL DESKTOP BOARD DG45ID

[. . . ] Intel may make changes to specifications and product descriptions at any time, without notice. Intel Desktop Board DG43RK may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be obtained from Intel Corporation by going to the World Wide Web site at: http://intel. com/ or by calling 1-800-548-4725. Intel and the Intel logo are trademarks of Intel Corporation in the U. S. All rights reserved. Preface This Product Guide gives information about board layout, component installation, BIOS update, and regulatory requirements for Intel Desktop Board DG43RK. Intended Audience The Product Guide is intended for technically qualified personnel. It is not intended for general audiences. Use Only for Intended Applications All Intel Desktop Boards are evaluated as Information Technology Equipment (I. T. E. ) for use in personal computers (PC) for installation in homes, offices, schools, computer rooms, and similar locations. [. . . ] Use DDR3 DIMMs 40 Installing and Replacing Desktop Board Components To install a DIMM, follow these steps: 1. Remove the computer?s cover and locate the DIMM sockets (see Figure 17). Figure 17. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position. Holding the DIMM by the edges, remove it from its anti-static package. Align the small notch at the bottom edge of the DIMM with the key in the socket (see inset in Figure 17). 41 Intel Desktop Board DG43RK Product Guide 7. When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips snap into place. Replace the computer?s cover and reconnect the AC power cord. Removing DIMMs To remove a DIMM, follow these steps: 1. Hold the DIMM by the edges, lift it away from the socket, and store it in an anti-static package. Reinstall and reconnect any parts you removed or disconnected to reach the DIMM sockets. Replace the computer?s cover and reconnect the AC power cord. 42 Installing and Replacing Desktop Board Components Installing and Removing a PCI Express x16 Card CAUTION When installing a PCI Express x16 card on the Desktop Board, ensure that the card is fully seated in the PCI Express x16 connector before you power on the system. If the card is not fully seated in the PCI Express connector, an electrical short may result across the PCI Express connector pins. Front Panel Audio Header Signal Names for Intel HD Audio Pin 1 3 5 7 9 Signal Name PORT 1L (Microphone) PORT 1R (Microphone) PORT 2R (Headphone) SENSE_SEND PORT 2L (Headphone) Pin 2 4 6 8 10 Signal Name GND PRESENCE# SENSE1_RETURN KEY (no pin) SENSE2_RETURN Table 7. Front Panel Audio Header Signal Names for AC ?97 Audio Pin 1 3 5 7 9 Signal Name MIC MIC_BIAS FP_OUT_R No connection FP_OUT_L Pin 2 4 6 8 10 Signal Name AUD_GND PRESENCE# AUD_GND KEY (no pin) AUD_GND 48 Installing and Replacing Desktop Board Components IEEE 1394a Header See Figure 22, C for the location of the IEEE 1394a header. IEEE 1394a Header Signal Names Pin 1 3 5 7 9 Signal Name TPA1+ Ground TPA2+ +12 V Key (no pin) Pin 2 4 6 8 10 Signal Name TPA1Ground TPA2+12 V Ground Parallel Port Header See Figure 22, D for the location of the parallel port header. Parallel Port Header Signal Names Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Standard Signal Name STROBE# AUTOFD# PD0 FAULT# PD1 INT# PD2 SLCTIN# PD3 GROUND PD4 GROUND PD5 GROUND PD6 GROUND PD7 GROUND ACK# GROUND BUSY GROUND ECP Signal Name STROBE# AUTOFD#, HOSACK PD0 FAULT#, PERIPHREQST# PD1 INT#, REVERSERQST# PD2 SLCTIN# PD3 GROUND PD4 GROUND PD5 GROUND PD6 GROUND PD7 GROUND ACK# GROUND BUSY#, PERIPHACK GROUND EPP Signal Name WRITE# DATASTB# PD0 FAULT# PD1 RESET# PD2 ADDRSTB# PD3 GROUND PD4 GROUND PD5 GROUND PD6 GROUND PD7 GROUND INTR GROUND WAIT# GROUND 49 Intel Desktop Board DG43RK Product Guide Pin 23 24 25 26 Standard Signal Name PERROR GROUND SELECT KEY (no pin) ECP Signal Name PE, ACKREVERSE# GROUND SELECT KEY (no pin) EPP Signal Name PE GROUND SELECT KEY (no pin) Serial Port Header See Figure 22, E for the location of the serial port header. Serial Port Header Signal Names Pin 1 3 5 7 9 Signal Name DCD TXD# Ground RTS RI Pin 2 4 6 8 10 Signal Name RXD# DTR DSR CTS No Connection Alternate Front Panel Power LED Header Figure 22, F shows the location of the alternate front panel power LED header. Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel header. If your chassis has a three-pin power LED cable, connect it to this header. Table 11 shows the pin assignments for the alternate front panel header. Alternate Front Panel Power LED Header Signal Names Pin 1 2 3 Signal Name Front panel green LED No pin Front panel yellow LED Out In/Out Out 50 Installing and Replacing Desktop Board Components Front Panel Header See Figure 22, G for the location of the front panel header. Front Panel Header Signal Names Pin 1 3 5 7 9 Signal Name Hard Drive Activity LED Hard disk LED pull-up to +5 V Out Hard disk active LED Reset Switch Ground Reset switch Power Power Out 10 No pin In 6 8 Ground Not Connected Out 2 4 In/Out Pin Signal Name Power LED Front panel green LED Front panel yellow LED On/Off Switch Power switch In Out Out In/Out USB 2. 0 Headers See Figure 22, H for the location of the three USB 2. 0 headers. USB 2. 0 Header Signal Names USB Port A Pin 1 3 5 7 9 Signal Name Power (+5 V) DD+ Ground Key Pin 2 4 6 8 10 USB Port B Signal Name Power (+5 V) DD+ Ground No Connection Note: USB ports may be assigned as needed. NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. [. . . ] Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the user?s authority to operate the equipment. Tested to comply with FCC standards for home or office use. Canadian Department of Communications Compliance Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le prsent appareil numerique nmet pas de bruits radiolectriques dpassant les limites applicables aux appareils numriques de la classe B prescrites dans le Rglement sur le broullage radiolectrique dict par le ministre des Communications du Canada. Japan VCCI Statement Japan Statement translation: This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). [. . . ]