User manual INTEL D865GLC

[. . . ] Intel® Desktop Board D865GBF/D865GLC Product Guide Order Number: C24485-002 Revision History Revision -001 -002 Revision History First release of the Intel® Desktop Board D865GBF/D865GLC Product Guide. Second release of the Intel® Desktop Board D865GBF/D865GLC Product Guide. Date March 2003 May 2003 If an FCC declaration of conformity marking is present on the board, the following statement applies: FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions related to the EMC performance of this product, contact: Intel Corporation 5200 N. E. [. . . ] Table 8 shows the pin assignments for the front panel audio header. Table 8. Pin 1 3 5 7 9 Front Panel Audio Header Signal Names (J9A2) Signal Name AUD-MIC AUD-MIC-BIAS AUD-FPOUT-R HP-ON AUD-FPOUT-L Pin 2 4 6 8 10 Signal Name AUD-GND AUD-VCC AUD-RET-R KEY AUD-RET-L To install the cable that connects the front panel audio solution to the front panel audio header, follow these steps: 1. Remove the two jumpers from the header to disable the back panel audio connectors. Replace the cover. 41 Intel Desktop Boards D865GBF/D865GLC Product Guide Setting up the Flexible 6-Channel Audio with Jack Sensing After installing the SoundMAX 4 XL audio driver from the Intel Express Installer CD-ROM, the multi-channel audio feature can now be enabled. See Figure 14 for back panel audio connectors. A B C OM15694 Item A B C Description Rear left/right out or Line In Front left/right out or S/PDIF line out Center-LFE (Subwoofer) or Mic In Figure 14. Back Panel Audio Connectors for 6-Channel Audio with Jack Sensing Multi-Channel Analog Audio Connect two speakers to the front left/right out (B) and two speakers to the r left/right out (A) for both 4- and 6-channel audio configurations. For 6-channel audio, connect two additional speakers to the center-LFE (C). Multi-Channel Digital Audio To take advantage of the S/PDIF functionality, a 1/8-inch stereo phone plug to the RCA jack adapter/splitter is required to convert from the stereo input to RCA connection. Connect the stereo input side of the adapter to the S/PDIF (B) connector, and connect the speaker system or S/PDIF decoder to the RCA jack left channel (white, if colored). Related Link: For the location of the ATAPI-style audio headers, go to page 87 in Chapter 5. 42 Installing and Replacing Desktop Board Components Connecting USB 2. 0 Headers Before connecting USB 2. 0 headers, observe the precautions in "Before You Begin" on page 27. Figure 13-A and -B on page 40 shows the location of the USB 2. 0 headers. Table 9 shows the pin assignments for the headers. Table 9. Pin 1 3 5 7 9 USB 2. 0 Headers (J9F1 and J9H1) USB Port A Signal Name Power DD+ Ground Key (no pin) Pin 2 4 6 8 10 USB Port B Signal Name Power DD+ Ground Not connected Note: USB ports may be assigned as needed. Connecting the Front Panel Header Before connecting the front panel header, observe the precautions in "Before You Begin" on page 27. Table 10 shows the pin assignments for the front panel header. Table 10. Pin Signal 1 3 HD_PWR HDA# Front Panel Header (J9J1) In/Out Out Out Description Hard disk LED pullup (330 ) to +5 V Hard disk active LED Pin Signal 2 4 In/Out Description Front panel green LED Front panel yellow LED Hard Drive Activity LED Power LED HDR_BLNK_GRN Out HDR_BLNK_YEL Out Reset Switch 5 7 9 Ground FP_RESET# +5 V In Out Ground Reset switch Power 6 8 10 Ground N/C On/Off Switch SWITCH_ON# In Power switch Ground Not connected 43 Intel Desktop Boards D865GBF/D865GLC Product Guide Connecting Hardware Control and Power Cables Figure 15 shows the location of the chassis intrusion and fan headers, and power connectors. Chassis rear fan 1 J6B1 12 V processor core voltage connector 1 2 Processor fan 1 J6B1 Chassis intrusion connector 1 1 Chassis front fan Main power connector 2 1 J9H2 J7J3 OM15237 Figure 15. Location of Hardware Control Headers and Power Connectors 44 Installing and Replacing Desktop Board Components Connecting the Chassis Intrusion Cable Connect the chassis intrusion cable to the header shown in Figure 15. Connecting Fans Connect the processor's fan heat sink cable to the processor fan header on the board. See Figure 15 for fan header locations. Connecting Power Cables CAUTION Failure to use an ATX12V power supply, or not connecting the 12 V processor core voltage power supply connector to the desktop board may result in damage to the desktop board and/or power supply. Connect the 12 V processor core voltage power supply cable to the 2x2 connector. Connect the main power cable to the 2x10 connector. 45 Intel Desktop Boards D865GBF/D865GLC Product Guide Setting the BIOS Configuration Jumper Block CAUTION Always turn off the power and unplug the power cord from the computer before changing the jumper. Moving the jumper with the power on may result in unreliable computer operation. The location of the desktop board's BIOS configuration jumper is shown in Figure 16. 1 3 J9J4 OM15233 Figure 16. Location of the BIOS Configuration Jumper Block The three-pin BIOS jumper block enables all board configurations to be done in BIOS Setup. Table 11 shows the jumper settings for the Setup program modes. Table 11. Jumper Settings for the BIOS Setup Program Modes (J9J4) Mode Normal (default) (1-2) Configure (2-3) Description The BIOS uses the current configuration and passwords for booting. After the Power-On Self-Test (POST) runs, the BIOS displays the Maintenance Menu. The BIOS recovers data from a recovery diskette in the event of a failed BIOS update. Jumper Setting 1 3 1 3 1 3 Recovery (None) 46 Installing and Replacing Desktop Board Components Clearing Passwords This procedure assumes that the board is installed in the computer and the configuration jumper block is set to normal mode. [. . . ] Updated Failed Keyboard Is Locked Keyboard Error KB/Interface Error BIOS Error Messages Explanation An error occurred with Gate-A20 when switching to protected mode during the memory test. Could not read sector from corresponding drive. Error Message Corresponding drive is not an ATAPI device. Run Setup to make sure device is selected correctly. No response from the diskette drive. continued 92 Error Messages and Indicators Table 42. BIOS Error Messages (continued) Explanation Memory size has decreased since the last boot. [. . . ]