User manual INTEL D845HV

[. . . ] Intel® Desktop Board D845HV/D845WN Technical Product Specification August 2001 Order Number: A65136-001 The Intel® Desktop Boards D845HV/D845WN may contain design defects or errors known as errata that may cause the product to deviate from published specifications. Current characterized errata are documented in the Intel Desktop Board D845HV/D845WN Specification Update. Revision History Revision -001 Revision History First release of the Product Specification. Intel ® Desktop Board D845HV/D845WN Technical Date August 2001 This product specification applies to only standard D845HV and D845WN boards with BIOS identifier HV84510A. 86A. Changes to this specification will be published in the Intel Desktop Board D845HV/D845WN Specification Update before being incorporated into a revision of this document. INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. [. . . ] Table 41 on page 69 lists the names of the signals available on this connector when no jumpers are installed. Jumper Setting 1 3 5 7 9 10 2 4 6 1 3 5 7 9 2 4 6 10 NOTE When the jumpers are removed and this connector is used for front panel audio, the back panel audio line out and mic in connectors are disabled. 2. 9. 2 BIOS Setup Configuration Jumper Block The 3-pin jumper block determines the BIOS Setup program's mode. Table 49 describes the jumper settings for the three modes: normal, configure, and recovery. When the jumper is set to configuration mode and the computer is powered-up, the BIOS compares the processor version and the microcode version in the BIOS and reports if the two match. Table 49. Normal 1-2 3 BIOS Setup Configuration Jumper Settings Jumper Setting 1 Function/Mode Configuration The BIOS uses current configuration information and passwords for booting. A recovery diskette is required. Configure 2-3 1 3 Recovery None 1 3 For information about How to access the BIOS Setup program The maintenance menu of the BIOS Setup program BIOS recovery Refer to Section 4. 1, page 95 Section 4. 2, page 96 Section 3. 7, page 91 73 Intel Desktop Board D845HV/D845WN Technical Product Specification 2. 10 Mechanical Considerations 2. 10. 1 D845HV Form Factor The D845HV board is designed to fit into either a microATX or an ATX-form-factor chassis. Figure 17 illustrates the mechanical form factor for the D845HV board. The outer dimensions are 9. 60 inches by 9. 60 inches [243. 84 millimeters by 243. 84 millimeters]. Location of the I/O connectors and mounting holes are in compliance with the ATX specification (see Section 1. 4). NOTE When installing the board in a microATX chassis, make sure that peripheral devices are installed at least 1. 5 inches above the main power connector, the diskette drive connector, and the IDE connector, and the DIMM sockets. 6. 50[165. 10] 6. 10[154. 94] 5. 20[132. 08] 0. 00 2. 85[72. 39] 3. 10[78. 74] 9. 05[229. 87] 0. 55[13. 97] 0. 00 0. 80 [20. 32] 2. 60 [66. 04] 8. 80 [223. 52] OM11436 Figure 17. D845HV Board Dimensions 74 Technical Reference 2. 10. 2 D845WN Form Factor The D845WN board is designed to fit into an ATX-form-factor chassis. Figure 18 illustrates the mechanical form factor for the D845WN board. The outer dimensions are 12. 00 inches by 9. 60 inches [304. 48 millimeters by 243. 84 millimeters]. Location of the I/O connectors and mounting holes are in compliance with the ATX specification (see Section 1. 4). 6. 50 [165. 10] 6. 10 [154. 94] 5. 20 [132. 08] 0. 00 2. 85 [72. 39] 3. 10 [78. 74] 2. 95 [74. 93] 9. 05 [229. 87] 8. 80 [223. 52] OM11437 0. 00 2. 30 [58. 42] 0. 80 [20. 32] 2. 60 [66. 04] Figure 18. D845WN Board Dimensions 75 Intel Desktop Board D845HV/D845WN Technical Product Specification 2. 10. 3 I/O Shield The back panel I/O shield for D845HV and D845WN boards must meet specific dimension and material requirements. Systems based on this board need the back panel I/O shield to pass certification testing. Figure 19 shows the critical dimensions of the chassis-dependent I/O shield for boards with the onboard LAN subsystem. Figure 20 shows the critical dimensions of the I/O for boards without the onboard LAN subsystem. Additional design considerations for I/O shields relative to chassis requirements are described in the ATX specification. See Section 1. 4 for information about the ATX specification. NOTE The I/O shield drawings in this document are for reference only. An I/O shield compliant with the ATX chassis specification 2. 01 is available from Intel. 6. 390 Ref [162. 300] 0. 063±0. 005 [1. 600±0. 120] 0. 787±0. 010 TYP [20±0. 254] 0. 039 Dia. [1. 000] 0. 884 [22. 450] 0. 276 [7. 012] 0. 00 0. 465 [11. 811] 0. 567 [14. 400] 3x Dia 0. 330 [8. 380] 8X R0. 5 MIN 0. 519 [13. 190] 0. 027 [0. 690] 1. 89 Ref 0. 465 [11. 811] 0. 567 [14. 400] 0. 621 [15. 770] 2. 079 [52. 804] 5. 010 [127. 250] 5. 732 [145. 584] 1. 195 [30. 360] 0. 447 [11. 345] 1. 807 [45. 892] 0. 00 Pictorial View OM12352 Figure 19. I/O Shield Dimensions (for boards with the LAN Subsystem) 76 Technical Reference 6. 390 Ref [162. 300] 0. 063±0. 005 [1. 600±0. 120] 0. 787±0. 010 TYP [20±0. 254] 0. 039 Dia. [1. 000] 0. 884 [22. 450] 0. 276 [7. 012] 0. 00 0. 465 [11. 811] 0. 567 [14. 400] 3x Dia 0. 330 [8. 380] 8X R0. 5 MIN 0. 519 [13. 190] 0. 027 [0. 690] 1. 89 Ref 0. 465 [11. 811] 0. 567 [14. 400] 0. 621 [15. 770] 2. 079 [52. 804] 5. 010 [127. 250] 5. 732 [145. 584] 1. 195 [30. 360] 0. 447 [11. 345] 1. 807 [45. 892] 0. 00 Pictorial View OM12353 Figure 20. I/O Shield Dimensions (for boards without the LAN Subsystem) 77 Intel Desktop Board D845HV/D845WN Technical Product Specification 2. 11 Electrical Considerations 2. 11. 1 · · · · · Power Consumption Table 50 lists voltage and current measurements for a computer that contains the D845HV/D845WN board and the following: 1. 7 GHz Intel Pentium 4 processor with a 256 KB cache 256 MB SDRAM 3. 5-inch diskette drive 20 GB IDE hard disk drive 32X IDE CD-ROM drive This information is provided only as a guide for calculating approximate power usage with additional resources added. [. . . ] Going to check for memory wrap around at 0:0 and finding the total system memory size. Check for soft reset and going to clear memory below 1M for soft reset. Clearing output buffer, checking for stuck key, to issue keyboard reset command. continued 123 Intel Desktop Board D845HV/D845WN Technical Product Specification Table 84. Code 84 85 86 87 88 89 8B 8C 8D 8F 91 95 96 97 98 99 9A 9B 9C 9D 9E A2 A3 A4 A5 A7 A8 A9 AA AB AC AD Runtime Code Uncompressed in F000 Shadow RAM (continued) Description of POST Operation Lock-key checking over. [. . . ]