User manual HARMAN KARDON SIGNATURE 1.5

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HARMAN KARDON SIGNATURE 1.5. We hope that this HARMAN KARDON SIGNATURE 1.5 user guide will be useful to you.


HARMAN KARDON SIGNATURE 1.5 : Download the complete user guide (407 Ko)

Manual abstract: user guide HARMAN KARDON SIGNATURE 1.5

Detailed instructions for use are in the User's Guide.

[. . . ] 1. 5 Two-Channel Bridgeable Amplifier Owner's Manual Staple or clip your original invoice here. ¤ Signature 1. 5 Two-Channel Bridgeable Amplifier Owner's Manual Table of Contents Introduction . 12 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] To control the amplifier in this manner you will need a small UL/CSA-approved class-2 AC-to-DC power converter capable of delivering a 6- to 12-volt DC signal. The DC voltage should terminate in a standard 3. 5 mm mono miniplug, with the tip of the plug "positive" (+). This type of converter may be obtained as a "Power Adapter" from many electronics retailers. Consult your dealer for further information. Output Connections The final step of the installation process is to connect the amplifier to your speakers using high-quality cable. To ensure that the high-quality signals produced by the 1. 5 are carried to your speakers without loss of clarity or resolution, we recommend that you use high-quality 6 Signature 1. 5 speaker cable. Many brands of cable are available, and the choice of cable may be influenced by the distance between your speakers and the amplifier, the type of speakers you use, personal preferences and other factors. Your dealer or installer is a valuable resource to consult in selecting a proper cable for connections between your amplifier and speakers. Regardless of the brand or type of cable selected, we recommend that you use a cable constructed of highstrand-count copper with a gauge of 14 or smaller. When specifying cable, remember that the smaller the number, the thicker the cable. Cable with a gauge of 16 may be used for short runs of less than ten feet. We do not recommend the use of cables with an AWG equivalent of 18 or higher due to the power loss and degradation in performance that will occur. Cables run inside walls should have the appropriate markings to indicate listing with UL ("CL-2/CL-3"), CSA ("FT-4") or appropriate safety agency standards that may be required in your area. Questions about running cables inside walls should be referred to your installer or a licensed electrical contractor who is familiar with the NEC and/or the applicable building or electrical codes in your area. Two-Channel/Stereo Systems: When installing a twochannel (stereo) system, connect the positive (+) and negative ( ) terminals from the right and left speakers to the matching terminals ¡ ¢ on the rear panel of the 1. 5. Make certain that the Bridge/Normal Switch £ is in the NORMAL position (see page 8). When the 1. 5 is used for two-channel/stereo operation, speakers with an impedance of no less than 4 ohms may be used. Bridged Mono Applications: To use the 1. 5 as a singlechannel, mono amplifier, connect the (+) terminal on your speaker to the (+) terminal on the Channel Two Output ¢ on the 1. 5. Connect the negative ( ) terminal on your speaker to the positive (+) terminal on the Channel One Output ¡ (see page 9). Important Note: When the 1. 5 is used in the Bridged Mono mode, do not use speakers with an impedance of less than 8 ohms. Installation and Connections When making speaker connections, note that one conductor of the speaker cable may have no markings or an indication of ( ) for negative polarity, and the other will have a red line, brand-name markings, a colored thread or some other positive-polarity indication (+). - The wire with the positive indication should be connected to the red terminals on both the 1. 5 and your speakers. The negative wire should be connected to the black terminal on the 1. 5 and the speakers. If bare wire is used for connections, strip approximately 3/4(20 mm) of insulation from the end of each wire and carefully twist the strands of each conductor together. Be careful not to cut the individual strands or twist them off; for optimal performance, all strands must be used. [. . . ] There are no controls to adjust once the installation is complete. Manual Operation For conventional, standalone operation, first make all connections to speakers and input sources as outlined on the previous pages. Make certain that the front panel Power Switch 1 is in the fully extended "off" position and then connect the AC Power Cord ¶ to a wallmounted AC outlet with sufficient current capacity. To turn the unit on, press the front panel Power Switch 1 until it is flush with the front panel. Once the switch is turned on, the 1. 5 will go into a brief Warm-Up mode, as indicated by the LED Indicator 3 flashing green. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HARMAN KARDON SIGNATURE 1.5




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HARMAN KARDON SIGNATURE 1.5 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.