User manual HARMAN KARDON HS 280
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HARMAN KARDON HS 280. We hope that this HARMAN KARDON HS 280 user guide will be useful to you.
You may also download the following manuals related to this product:
HARMAN KARDON HS 280 (4702 ko)
HARMAN KARDON HS 280 (4781 ko)
HARMAN KARDON HS 280 (4712 ko)
HARMAN KARDON HS 280 (4707 ko)
HARMAN KARDON HS 280 (4728 ko)
HARMAN KARDON HS 280 (4716 ko)
HARMAN KARDON HS 280 (4704 ko)
Manual abstract: user guide HARMAN KARDON HS 280
Detailed instructions for use are in the User's Guide.
[. . . ] [. . . ] 8 Connect the speaker wire to the speaker terminals, as shown in the illustration below: a) Press down on the top of the terminal to open the connection hole b) Insert the wire's bare end all the way into the hole c) Release the terminal to secure the wire Insert the conductor with the colored band into the speaker's red ( + ) terminal Insert the other conductor into the speaker's black ( ) terminal
Wall-Mounting the HS 210 Satellite Speakers
Unscrew the bolt that attaches the black shelf stand to the bottom of the speaker Store the stand and bolt in a safe place in case you need them for a future installation
Remove Stand 15 mm (M6-1 25P or 1 4"-20) Wall Plate
Mount the wall-bracket attachment plate on the wall
+
If possible, position the speakers so that the mounting screws (not included; use size #8) may be installed directly into a wooden wall stud If that is not possible, use optional wall anchors that are rated to support at least twenty-five pounds The customer is responsible for proper selection and use of mounting hardware, available through hardware stores, to wall-mount the speakers properly and safely.
A Push Down on Cap to Open Hole
B Insert Base Wire into Open Hole
C Release Cap to Secure Wire
13
ENGLISH
5 If you're not running the speaker wire through the wall, insert it through the wall portion of the wall-mount bracket, as shown in the illustration below
IMPORTANT: Make sure the ( + ) and ( ) bare wires do not touch each other or the other terminal Touching wires can cause a short circuit that can damage the receiver
For the speaker-connection instructions on pages 6 through 9, thread the appropriate speaker cable through the opening in the bottom of the attachment plate and then through the back of the bracket, as shown in the diagram
Wires to Speaker Terminal Cover Wire From Wall Plate Overhead View
The bracket has two openings on top: a round screw hole and an arc-shaped opening in front of it Thread the speaker cable through the arcshaped opening, not the screw hole Attach the bracket to the wall plate by inserting the tab at the top of the attachment plate into the slot on top of the bracket and snapping the bracket onto the attachment plate
It is very important to connect each speaker identically: ( + ) on the speaker to ( + ) on the receiver or amplifier, and ( ) on the speaker to ( ) on the receiver or amplifier. Miswiring one or more speakers results in thin sound, weak bass and a poor stereo image To connect the speaker wire to the terminals on the satellite speakers: 1 Press down on the top of the terminal to open the connection hole 2 Insert the wire's bare end all the way into the hole Insert the conductor with the colored band into the speaker's red ( + ) terminal, and insert the other conductor into the speaker's black ( ) terminal 3 Release the terminal to secure the wire to the terminals
+
Thread the cable through the round opening in the terminal cover Insert the speaker wires into the terminals on the underside of the speaker, remembering to observe the correct polarity (see "Speaker Connections") Place the terminal cover over the opening on the underside of the speaker so that it fits flush against the speaker and covers the terminals, with its round opening exposing the threaded insert The bracket fits through the round opening in the terminal cover Insert the supplied bracket bolt up through the bottom of the bracket and terminal cover Screw it into the threaded insert on the underside of the speaker The bolt should be snug, but not so tight as to prevent the bracket from pivoting
Wall Bracket
A Push Down on Cap to Open Hole
B Insert Base Wire into Open Hole
C Release Cap to Secure Wire
IMPORTANT: Make sure the ( + ) and ( ) bare wires do not touch each other or the other terminal Touching wires can cause a short circuit that can damage the receiver To connect the speaker wire to the terminals on the receiver: 1 Unscrew the connector sleeve to expose the hole in the connector post CAUTION: Take care not to unscrew the sleeve completely off the post 2 Insert the wire's bare end through the hole in the post Insert the conductor with the red colored band into the receiver's red ( + ) terminal Insert the conductor with the white colored band into the receiver's white ( + ) terminal Insert the unmarked conductors into the receiver's black ( ) terminals 3 Tighten the connector sleeve to secure the wire
The wall-mounted speaker may be pivoted from side to side; however, the bracket is not designed to tilt up or down, and attempting to tilt it will damage the bracket and possibly the wall Your warranty will not cover the damage
Wall
23 mm
A Unscrew Cap (M6-1 25P or 1 4"-20)
B Insert Bare Wire
C Tighten Cap
IMPORTANT: Make sure the ( + ) and ( ) bare wires do not touch each other or the other terminal Touching wires can cause a short circuit that can damage the receiver
Connections
CAUTION: Before connecting anything to the HS 280/HS 210, ensure that the HS 280/HS 210 receiver is turned Off and the receiver's AC cord is unplugged from the receiver and the AC outlet.
Connect the left and right speakers with supplied bases:
1 Remove the speaker's base (see Shelf Placement, on page 12) 2 Pass the speaker wire through the opening in the speaker base 3 Connect the speaker wire as described above 4 Reattach the speaker's base as shown in the illustration
Connecting the Satellite Speakers
Speakers and receivers/amplifiers have corresponding ( + ) and ( ) connection terminals · Your system's SAT TS60 left and right speakers use red to denote the ( + ) terminal and black for the ( ) terminal · The HS 280/HS 210 receiver uses white to denote the left channel ( + ) terminal and red for the right channel ( + ) terminal · Black is used to denote the ( ) terminal of both channels The speaker wires included with your system have colored bands at both ends of the ( + ) conductor; the colors correspond to the receiver's ( + ) terminal colors The subwoofer cable has purple connectors that correspond to the color of the receiver's subwoofer output and the color of the HKTS200SUB subwoofer's LFE jack This system helps you connect each speaker to the correct receiver or amplifier terminals In addition to the colored bands at each end, each speaker wire's ( + ) terminal has ribs molded into its insulation to help you identify it
Slide Base Straight onto Speaker Rails
5
14
Follow the instructions in Wall-Mounting the Satellite Speakers, on page 12
Connecting the Subwoofer
Use the LFE (purple) connectors of the supplied combination LFE and trigger cable to connect the HKTS200SUB subwoofer's Line-Level LFE In connector to the HS 280/ HS 210 receiver's Subwoofer Output Use the trigger (black) connectors of the supplied combination LFE and trigger cable to connect the subwoofer's External Trigger Input Connector to the HS 280/HS 210 receiver's Sub Trigger Output IMPORTANT: Do not plug the subwoofer's AC power cord into an AC outlet at this time
Right Satellite Right Satellite
Left Satellite Left Satellite
Front Right Satellite Cable Front Right Satellite (Red Bands) Cable (Red Bands)
Front Left Satellite Cable Front Left Satellite Cable (White Bands) (White Bands)
+
+
CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LOUKAN 1 LASER LAITE KLASS 1 LASER APPARAT
IN
OUT
+
CAUTION ATTENTION
FRONT R
RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE D' ELECTROCUTION NE PAS OUVRIR
SPEAKER OUTPUTS
FRONT L
+
Caution: Laser radiation when open. Do not start into beam.
ETHERNET
HDMI OUT
REMOTE CONTROL
COMPOSITE
S-VIDEO
WARNING: SHOCK HAZARD. - DO NOT OPEN AVIS: RISQUE DE CHOCK ELECTRIQUE - NE PAS OUVRIR
COAXIAL 1 IN
COAXIAL OUT OPTICAL 1 IN OPTICAL 2 IN
LINE OUT L
LINE 1 IN L
LINE 2 IN L TV
Apparatus Claims of U. S. Patent Nos. [. . . ] [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HARMAN KARDON HS 280
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HARMAN KARDON HS 280 will begin.