User manual HARMAN KARDON DPR 1005
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HARMAN KARDON DPR 1005. We hope that this HARMAN KARDON DPR 1005 user guide will be useful to you.
You may also download the following manuals related to this product:
HARMAN KARDON DPR 1005 (922 ko)
HARMAN KARDON DPR 1005 (948 ko)
HARMAN KARDON DPR 1005 (972 ko)
HARMAN KARDON DPR 1005 (935 ko)
HARMAN KARDON DPR 1005 (955 ko)
HARMAN KARDON DPR 1005 (953 ko)
HARMAN KARDON DPR 1005 (951 ko)
HARMAN KARDON DPR 1005 (917 ko)
HARMAN KARDON DPR 1005 BROCHURE (1773 ko)
HARMAN KARDON DPR 1005 annexe 1 (996 ko)
HARMAN KARDON DPR 1005 DEVICE PRIORITY ADDENDUM (48 ko)
HARMAN KARDON DPR 1005 DPR 1005 QUICK START GUIDE (533 ko)
HARMAN KARDON DPR 1005 PRODUCT ILLUS. GUIDE – FRONT PANEL CONTROLS (149 ko)
HARMAN KARDON DPR 1005 PRODUCT ILLUS. GUIDE – REAR PANEL CONNECTIONS (157 ko)
HARMAN KARDON DPR 1005 PRODUCT ILLUS. GUIDE – MAIN REMOTE CONTROL FUNCTIONS (72 ko)
HARMAN KARDON DPR 1005 PRODUCT ILLUS. GUIDE – ZONE II REMOTE CONTROL FUNCTIONS (28 ko)
Manual abstract: user guide HARMAN KARDON DPR 1005
Detailed instructions for use are in the User's Guide.
[. . . ] ®
Power for the Digital Revolution.
®
DPR 1005
DIGITAL PATH RECEIVER OWNER'S MANUAL
DPR 1005 DIGITAL PATH RECEIVER
3 4 4 5 8 11 15 16 19 19 19 20 22 22 24 26 27 27 28 30 30 30 30 30 31 31 32 35 35 35 36 37 37 37 37 37 38 39 39 39 40 41 41 41 42 42 43 44 46 47 48 49 51 51 52 Introduction Important Safety Information Unpacking Front-Panel Controls Rear-Panel Connections Main Remote Control Functions Zone II Remote Control Functions Installation and Connections System Configuration Speaker Placement System Setup Input Setup Audio Setup Surround Setup Speaker Setup Delay Settings Output Level Adjustment Using EzSet Manual Output Level Adjustment Operation Basic Operation Source Selection 6/8-Channel Direct Input Volume and Tone Control Surround Mode Selection Digital Audio Playback Surround Mode Chart Tuner Operation Tape Recording Front-Panel Connections Output Level Trim Adjustment Advanced Features Front-Panel Display Fade Display Brightness Turn-On Volume Level Semi-OSD Settings Full-OSD Time-Out Adjustment Multiroom Operation Multiroom Setup Surround Amplifier Channel Assignment Multiroom Operation Configuring the Remote Programming Remote Codes Preprogrammed Code Entry Automatic Code Entry Learning Commands Changing Devices Macro Programming Punch-Through Configuration EzSet Configuration Renaming Resetting the Remote Troubleshooting Guide Processor Reset Technical Specifications
Typographical Conventions In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used. EXAMPLE (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack EXAMPLE (OCR type) indicates a message that is visible on-screen or on the front-panel information display EXAMPLE (Synchro type) indicates a message that is displayed on the remote control's LCD screen 1 (number in a square) indicates a specific front-panel control A (letter in a square) indicates a front-panel control that is behind the drop-down door ¡ (number in a circle) indicates a rear-panel connection a (number in an oval) indicates a button or indicator on the remote å (letter in an oval) indicates a button on the Zone II remote
See trademark acknowledgements on page 52.
2
TABLE OF CONTENTS
INTRODUCTION
Thank You for Choosing Harman Kardon® With the purchase of a Harman Kardon DPR 1005, you are about to begin many years of listening enjoyment. Thanks to its completely digital path system, the DPR 1005 is truly a receiver for the new millennium. The DPR 1005 has a wide range of features and options that accommodate virtually any combination of speakers, room size and program sources. [. . . ] You may also make these same adjustments with complete manual control over the channel being adjusted by pressing the //¤ Navigation Button o until the cursor is pointing to the TEST TONE SEQ line on the menu and then using the </> Navigation Button o to select MANUAL in the highlighted video. In the MANUAL mode, the test tone will also start immediately, but the tone will only be moved to another channel by pressing the //¤ Navigation Button o. When the manual sequencing mode is active, the tone is turned off by pressing the //¤ Navigation Button o until the cursor is pointing to the TEST TONE line and the </> Navigation Button o is then pressed to select OFF in the highlighted video. The DPR's EzSet feature may also be used as an SPL meter to assist in accurate setting of the output levels, when either the internal test tone or an external source such as a test disc is used. Press and hold the SPL Select Button 45 until the red LED under the Set Button q lights and the LCD screen in the remote changes to the display shown in Figure 10. Press the / Navigation Button o once to change the bottom line of the remote's LCD display to read MANUAL SPL as shown in Figure 14.
SET SPKR LEVELS MANUAL SPL
* F C F S C T T B L E R R H E E A
CHANNEL :0 :0 :0 :0 NEL TO TO TO d d d d
ADJUST
*
N
A S S C
N T T K
B SBR B SBL B SL B SUB RESET NE SEQ NE MASTER
:0 dB :0 dB :0 dB :0 dB :OFF ON :AUTO :OFF ON MENU
Figure 13
Manual output level adjustment is most easily done through the CHANNEL ADJUST menu (Figure 13). If you are already at the MASTER MENU, press the ¤ Navigation Button o until the on-screen cursor is next to the CHANNEL ADJUST line. If you are not at the MASTER MENU, press the OSD Button U to bring up the MASTER MENU (Fig. 1), and then press the ¤ Navigation Button o until the on-screen cursor is next to the CHANNEL ADJUST line. Press the Set Button q to bring the CHANNEL ADJUST menu (Figure 13) to the screen. If desired, you may immediately use the //¤ Navigation Button o to select any channel for adjustment using an external source, such as a test disc, from which to judge the output levels. After the cursor is pointing to the channel to be adjusted, press the </> Navigation Button o to raise or lower the output level. However, before proceeding with any manual adjustment we recommend that you first use the DPR's internal test tone generator and automatic sequencer to send a tone to each channel so that you may verify that all speaker connections have been properly made. To turn the test tone on and have it automatically circulate among the channels where a speaker has previously been configured (see page 24), press the //¤ Navigation Button o until the cursor is pointing to the TEST TONE line on the menu. Next, press the </> Navigation Button o until AUTO SEQ is shown in highlighted video. At this time the test tone will immediately begin to circulate clockwise around the room, playing for two seconds in each speaker before switching to the next speaker position. The cursor will blink next to the active speaker to indicate which speaker the sound should be coming from. As the test noise circulates, listen to make certain that the sound comes from the speaker position shown in the Lower Display Line &. If the sound from a speaker location does NOT match the position indicated in the display, turn the DPR 1005 off using the Main
Manual Output Level Adjustment
Output levels may also be adjusted manually, either to set them to a specific level with an SPL meter, or to make fine tuning adjustments to the levels obtained using the EzSet remote.
Figure 14
28
SYSTEM CONFIGURATION
SYSTEM CONFIGURATION
3. Press the Set Button q within five seconds to activate the remote's manual mode, so that it functions as an SPL meter. The right corner of the bottom line of the remote's display will show the output level of the speakers as the test tone circulates. When you are finished with all adjustments, press the Clear Button 9 to return the remote to normal operation. [. . . ] message will appear in the upper line of the remote's LCD screen as shown in Figure 78. It may take a few minutes for the reset process to take place, and the length of time will vary depending on how much customization and programming has taken place. Please be patient; as long as the message appears in the display the remote is functioning properly.
RESETTING. . .
Figure 78
4. When the remote has been totally reset and returned to the factory default condition, a REMOTE RESET COMPLETE message will appear (Figure 79) briefly, and then the remote will return to normal operation.
REMOTE RESET COMPLETE
Figure 81
Figure 79
· The remote has a built-in backlight that may be activated by pressing the Light Button P. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HARMAN KARDON DPR 1005
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HARMAN KARDON DPR 1005 will begin.