User manual HARMAN KARDON AVR 160

[. . . ] AVR 160 AUDIO/VIDEO RECEIVER OWNER'S MANUAL SAFETY INFORMATION Important Safety InStructIonS 1. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. [. . . ] NOTE: If there are fewer than five main speakers in your system, do not use the EzSet/EQ process. If you have selected a 6. 1-channel configuration with a single surround back speaker, use EzSet/EQ automatic configuration for 5. 1 speakers, connect the single surround back speaker to the left Surround Back Speaker Output, then configure the surround back speaker manually, as described in the Advanced Functions section. If the subwoofer is to be connected to the Front Speaker Outputs, do not connect the subwoofer until after running the EzSet/EQ process. The test will begin, and a screen such as the one shown in Figure 21 will appear. Maintain silence during the EzSet/EQ configuration. configure the aVr 160, using ezSet/eQ technology One of the most important steps in setting up a home theater system is to calibrate the receiver to match the loudspeakers, optimizing sound reproduction. Until recently, most receivers required manual calibration and configuration, a tedious process that called for a good ear or the purchase of an SPL (soundpressure level) meter. Although you may configure the AVR 160 manually, as described in the Advanced Functions section, it is recommended that you take advantage of the signature Harman Kardon EzSet/EQ system. Eliminate extraneous background noise, such as noisy air conditioning. IMPORTANT SAFETY NOTE: During the EzSet/EQ procedure, a series of very loud test sweeps will be played through all of the speakers. Avoid sitting or standing close to any one speaker during the procedure. If you are particularly sensitive to loud noises, you may wish to leave the room and have someone else run the EzSet/EQ process. 23 INITIAL SETUP Component In: If you connected the source to one of the two component video inputs, press the N Button to adjust the setting if needed. NOTE: If the source is connected to a composite video input but a signal is present at the selected component video input, the AVR will display the component video signal. To avoid this, turn off the component video source device, or adjust this setting to select a component video input that is not in use. When no component video signal is present, the AVR will automatically select the composite video input associated with the source. Figure 21 ­ EzSet/EQ in Progress As the EzSet/EQ system tests each speaker, its position will appear on screen. If the test sweep is heard from a different speaker than the one indicated on screen, turn off the AVR and check the speaker-wire connections, then begin again. When the Speaker Detection test is completed, select the Continue option. The results will be displayed, along with these options: · The Retest option repeats the EzSet/EQ process. Increase the master volume manually, if some speakers were not correctly detected. See the Advanced Functions section for instructions on how to manually configure the speakers or manually adjust the settings established by the EzSet/EQ process. Audio In: If you used a digital audio connection for a source, change this setting to assign the correct digital audio input, even if you also connected its analog audio outputs to the receiver. Move the cursor to this line, and press the M N Buttons until the correct digital input appears. If an analog audio connection was used, change this setting to ANALOG. Auto Poll: The Auto Poll feature is used when both an analog audio and digital audio connection have been made for one source device. [. . . ] CH 1 2 3 4 5 6 7 8 TUN-M / 9 0 Memory / Tuning Up / RD Direct / GR Clear / YL Preset Up / BL Tuning Down Tone RDS Preset Down M1 M2 M3 M4 Night Skip Down Skip Up DIM Rew(G) Play( N) FF(H) Record (2) Stop (0) Pause (1) AVR AVR(001) Power On Power Off Mute AVR Power On DVD VID1 HDMI 1 AM/FM CD VID2 HDMI 2 AUX TAPE VID3 HDMI3 Sleep Test Tone 6/8 CH Vol Up OSD Vol Down Channel Speaker Level+/Up Left OK Right Level-/Down Digital Delay 1 2 3 4 5 6 7 8 TUN-M 9 0 Memory Tuning Up Direct Clear Preset Up Tuning Down Tone Mode RDS Preset Down M1 M2 M3 M4 Night Skip Down(DVD) Skip Up(DVD) Dimmer Rew(DVD) Play(DVD) FF(DVD) Repeat(DVD) Stop(DVD) Pause(DVD) CD(001) Power On Power Off Mute(AVR) AVR Power On DVD VID1 HDMI 1 AM/FM CD VID2 HDMI 2 AUX TAPE VID3 HDMI3 CD CD(002) CDR Power On Power Off Mute(AVR) AVR Power On DVD VID1 HDMI 1 AM/FM CD VID2 HDMI 2 AUX TAPE VID3 HDMI3 CD(003) Power On Power Off Mute(AVR) AVR Power On DVD VID1 HDMI 1 AM/FM CD VID2 HDMI 2 AUX TAPE VID3 HDMI3 26 28 30 29 32 35 39 43 47 51 55 36 40 44 48 52 56 6/8 CH Intro Scan 6/8 CH Vol Up CDR Select Program Input Select Vol Down Continuous Play Intro Scan 6/8 CH Source Info 60 63 66 Open/Close 1 2 3 4 5 6 7 8 Repeat 9 0 Time Random Play (+10) 61 62 Open/Close 1 2 3 4 5 6 7 8 Repeat 9 0 Time Track Direct Random Play Clear Track Increment Program Open/Close 1 2 3 4 5 6 7 8 Repeat 9 0 Time Folder + Random Clear (10+) Folder ­ Disc Skip (10­) Skip Down Skip Up R. Search Record Stop Pause Figure 31 ­ Remote Control Function List Reference Previous Next Display Search ­ Play/Pause Search + Stop Play/Pause Refer to the numbered buttons in this image when using the Function List. 42 APPENDIX Table A10 ­ Remote Control Function List continued DVD Bluray(001) Power On Power Off Mute(AVR) AVR Power On DVD VID1 HDMI 1 AM/FM CD VID2 HDMI 2 AUX TAPE VID3 HDMI3 DVD(002) Power On Power Off Mute(AVR) AVR Power On DVD VID1 HDMI 1 AM/FM CD VID2 HDMI 2 AUX TAPE VID3 HDMI3 DVD(003) Power On Power Off Mute(AVR) AVR Power On DVD VID1 HDMI 1 AM/FM CD VID2 HDMI 2 AUX TAPE VID3 HDMI3 Audio 6/8 CH Title HD Mode V. OFF Disc Menu Setup Up Left Enter Right Down Open/Close Status 1 2 3 4 5 6 7 8 Zoom 9 0 Playlist Angle Clear AUX AUX(001) HDMI 1/2/3 HDMI1/2/3 Power On Power Off MUTE AVR Power On DVD VID1 HDMI 1 AM/FM CD VID2 HDMI 2 AUX TAPE VID3 HDMI3 PR+ 6/8 CH Vol Up PROSD TV/VCR Vol Down Guide Menu Up Left Set/Enter Right Down Prev. CH 1 2 3 4 5 6 7 8 9 0 VCR Power On Power Off MUTE AVR Power On DVD VID1 HDMI 1 AM/FM CD VID2 HDMI 2 AUX TAPE VID3 HDMI3 PR+ 6/8 CH Vol Up PROSD TV/VCR Vol Down Menu Up Left Enter Right Down -/-1 2 3 4 5 6 7 8 Slow Down 9 0 Slow Up Cancel Clear VID1 DMC 250/1000 Power On Power Off AVR Power On DVD VID1 HDMI 1 AM/FM CD VID2 HDMI 2 AUX TAPE VID3 HDMI3 Audio Find 6/8 CH Title Info Video Mode Disc Menu Setup Up Left Enter Right Down Open/Close Status 1 2 3 4 5 6 7 8 Zoom 9 0 Source Return Angle Clear CBL Power On Power Off MUTE AVR Power On DVD VID1 HDMI 1 AM/FM CD VID2 HDMI 2 AUX TAPE VID3 HDMI3 PR+ 6/8 CH Vol Up PROSD TV/CBL Vol Down INFO Menu Up Left Enter Right Down Prev. CH 1 2 3 4 5 6 7 8 9 0 PPV FAV Bypass Music VID2 SAT Power On Power Off MUTE AVR Power On DVD VID1 HDMI 1 AM/FM CD VID2 HDMI 2 AUX TAPE VID3 HDMI3 PR+ 6/8 CH Vol Up PROSD TV/SAT Vol Down INFO Menu Up Left Enter Right Down Prev. [. . . ]