User manual ESCALADE SPORTS G07130

[. . . ] BOX 889 EVANSVILLE, IN 47706 When contacting Escalade Sports please provide model number, serial number (if applicable), and part number if requesting a replacement part. These numbers can be found on the product, packaging, and in this Owner's Manual. For Customer Service Call 800-426-1421 1 REQUIRED TOOLS PHILLIPS SCREWDRIVER STANDARD SCREWDIVER ADJUSTABLE WRENCH OR STANDARD SOCKET SET 2 HARDWARE PARTS IDENTIFIER (ACTUAL SIZE MAY VARY) DESCRIPTION QTY. REQUIRED H1 H2 H3 H4 H5 H6 H7 H8 H9 5/16"x1-1/4" BOLT 16 1/4"x1-1/4" BOLT 16 1-1/4"FLAT HEAD PHILLIPS SCREW 34 5/8"ROUND HEAD PHILLIPS SCREW 1/4" LOCK HEX NUT 16 16 1" ROUND HEAD PHILLIPS SCREW 5 BRACKET(not actual size) 4 5/16"BLACK FLAT WASHER 1/4"BLACK FLAT WASHER 16 32 For Customer Service Call 800-426-1421 3 ACCESSORIES A1 A2 A3 A4 A5 A6 PARTS IDENTIFIER DESCRIPTION QTY BILLIARD BALL CHALK CUE STICK TRIANGLE BRUSH PLAYFIELD SPOT 1 2 2 1 1 2 ASSEMBLY PARTS DESCRIPTION P1B P1A QTY P1E P1D P1C P1F P1G P1 P1A MAIN ASSEMBLY LONG RAIL, A 1 1 For Customer Service Call 800-426-1421 4 ASSEMBLY PARTS P1B P1C P1D P1E P1F P1G PARTS IDENTIFIER DESCRIPTION LONG RAIL, B SHORT RAIL ENDS W/HOLE SHORT RAIL CENTER SHORT RAIL RETURN END HINGE, PRE-INSTALLED PLAYING SURFACE QTY 1 2 1 1 14 1 2 2 2 P2A P2B P3 P4 P5 P6A P6B LEG A, NOTE HOLE PLACEMENT LEG B, NOTE HOLE PLACEMENT LEG SIDE PANEL LEG END PANEL LEG LEVELER LONG RETURN BOARD, A LONG RETURN BOARD, B 2 4 1 1 For Customer Service Call 800-426-1421 5 ASSEMBLY PARTS P7A P7B P8 P9 P10 P11 P12 PART IDENTIFIER DESCRIPTION QTY APRON SIDE PANELS, RIGHT 1 APRON SIDE PANELS, LEFT 1 APRON END PANEL 1 APRON BALL RETURN PANEL 1 APRON CORNER 4 SHORT RETURN BOARD 1 GLUE 1 For Customer Service Call 800-426-1421 6 POOL TABLE ASSEMBLY ASSEMBLY INSTRUCTIONS WARNING:TWO ADULTS NEEDED TO ASSEMBLE POOL TABLE 1. [. . . ] THERE WILL BE A GROOVE RUNNING DIAGONALLY FROM LEFT TO RIGHT ON EACH PANEL. ATTACH AN APRON CORNER P10 TO THE END OF EACH APRON SIDE PANEL P7A AND P7B USING PHILLIPS HEAD SCREWS H4 WHERE THE GROOVE IS CLOSEST TO THE SCREW HOLES IN THE APRON SIDE PANEL P7A AND P7B NOTE:THE APRON CORNER P10 CAN ONLY BE INSTALLED AS THE ARROW INDICATED. P10 H4 P7A SCREW HOLES P7B SCREW HOLES For Customer Service Call 800-426-1421 11 ASSEMBLY INSTRUCTIONS WARNING:TWO ADULTS NEEDED TO ASSEMBLE POOL TABLE 10. POSITION APRON SIDE PANELS P7A AND P7B AS SHOWN AND ATTACH TO PLAYING SURFACE P1G USING PHILLIPS FLAT HEAD SCREWS H3 . BOARD IS POSITIONED CORRECTLY WHEN APRON CORNER P10 RESTS INSIDE CORNER CAP ATTACHED TO MAIN ASSEMBLY P1 . SLIDE THE APRON END PANEL P8 INTO EACH APRON CORNER P10 AND FASTEN USING PHILLIPS HEAD SCREWS H4 AND TO THE PLAYING SURFACE P1G USING FLAT HEAD PHILLIPS SCREWS H3. SLIDE LONG RETURN BOARD P6A INTO THE GROOVES OF THE APRON SIDE PANELS P7A AND LONG RAIL P1A . REPEAT ON OTHER SIDE BY SLIDING LONG RETURN BOARD P6B INTO THE GROOVES OF THE APRON SIDE PANELS P7B AND LONG RAIL P1B . NOTE: RUBBERIZED SIDES OF THE LONG RETURN BOARDS P6A AND P6B SHOULD FACE TOWARDS THE MAIN ASSEMBLY P1. (UPWARDS WITH TABLE UPRIGHTED) WITH ANGLED CORNERS TOWARDS APRON CORNERS P10 . POOL TABLE ASSEMBLY P7A P8 P1B P10 P6A P1A P1G P6B P7B H3 For Customer Service Call 800-426-1421 12 POOL TABLE ASSEMBLY ASSEMBLY INSTRUCTIONS WARNING:TWO ADULTS NEEDED TO ASSEMBLY 13. ATTACH AN APRON CORNER P10 TO EACH END OF THE APRON BALL RETURN PANEL P9 USING PHILLIPS HEAD SCREWS H4 NOTE : POSITION APRON CORNERS P10 SO THE SCREW HOLE IS NOT IN LINE WITH GROOVE FOR APRON BALL RETURN PANEL P9. ATTACH THE ASSEMBLED APRON BALL RETURN PANEL P9 TO BOTH APRON SIDE PANELS P7A AND P7B USING PHILLIPS HEAD SCREWS H4 AND ATTACH TO PLAYING SURFACE P1A USING PHILLIPS FLAT HEAD SCREWS H3. MAKE SURE APRON BALL RETURN PANEL "GROOVE"IS AWAY FROM PLAYING SURFACE (DOWN IF TABLE IS UPRIGHTED). NOTE : A TOTAL OF THREE SCREWS WILL BE PUT IN APRON CORNERS P10 AT THIS END OF TABLE-ONE YOU WILL NOT BE ABLE TO REACH BECAUSE OF CORNER CAP. P7A H4 P7B H3 P9 P10 For Customer Service Call 800-426-1421 13 POOL TABLE ASSEMBLY ASSEMBLY INSTRUCTIONS WARNING:TWO ADULTS NEEDED TO ASSEMBLE POOL TABLE 15. BEND SHORT RETURN BOARD P11 BY HAND AND INSERT INTO THE GROOVES OF BOTH APRON SIDE PANELS P7A AND P7B BY SLIDING IN X DIRECTION. SLIDE IN THE Y DIRECTION INTO THE GROOVES OF THE APRON BALL RETURN PANEL P9. POSITION THE METAL BRACKETS H7 AS SHOWN AND TAP DOWN INTO PLACE WITH A HAMMER. AFTER THE GLUE HAS DRIED AND IS SET (APPROXIMATELY 12 HOURS), TURN THE TABLE ASSEMBLY OVER TO RIGHT SIDE UP. PLACE A POOL BALL ON THE PLAYING SURFACE AND LEVEL THE TABLE BY TURNING THE LEG LEVELERS P5. P5 H6 P7A P11 H7 P7B P9 For Customer Service Call 800-426-1421 14 POOL TABLE ASSEMBLY ASSEMBLY INSTRUCTIONS WARNING:TWO ADULTS NEEDED TO ASSEMBLE POOL TABLE 20. [. . . ] The object balls are racked in a diamond shape, with the 1-ball in the foot spot at the front of the rack and the 9-ball in the center. A player keeps shooting as long as the player strikes the lowest numbered ball first and pockets a ball(it doesn't have to be the lowest number ball). if the shooter shoots the 1-ball into the 9-ball and pockets the 9-ball, the game is over. [. . . ]