User manual EDIROL V-44SW

[. . . ] Owner's Manual Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's Manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Copyright © 2006 ROLAND CORPORATION All rights reserved. [. . . ] For instructions on switching the input and output formats, refer to "Selecting NTSC or PAL Format" (p. 32) 2 Settings for the SD video input to the "SD section" If the Video is Disrupted There may be instances in which the level of the synchronization signal output by the SD video device is lower than the standard value, with disruption of the video resulting from the poor synchronization. System" in the menu and adjust the value in "3: SD Input Sync Threshold. " You may be able to synchronize the video and have it display properly. Settings in this section * Make the settings for 1 before the settings in 2 . 1 2 Press the [MENU] button to display the Main menu. SD Input" and then select the channel you want to set with "1: SD Ch1"­"4: SD Ch4" in the submenu. 55) 1: SD Input Select Selects the SD input Auto: The connector used for the SD signals being input is selected automatically. If SD signals are being input to both connectors on the same channel, the S-VIDEO IN connector is selected. Composite: Only the input from the COMPOSITE IN connector is selected. Brightness adjustment Contrast adjustment Saturation adjustment Hue adjustment Sets the Enable/Disable status for the channel select buttons For more detailed information, refer to the column, "To Prevent Errors in Using the Channel Select Buttons" (p. The sub-menu settings are returned to their factory default settings ( p. 29). 2: SD Brightness 3: SD Contrast 4: SD Saturation 5: SD Hue 6: SD Sw Enable 7: SD Reset 34 Setting the Input and Output Selecting NTSC or PAL Format The V-44SW's input and output formats are selectable; you can specify the NTSC format used in Japan and the United States or the PAL format used in Europe. Switch to the format suited to your needs. Switching the input and output formats also switches the frame rate of the output format of component (p. With NTSC format: With PAL format: Frame rate of "60" frames per second Frame rate of "50" frames per second Displaying a Test Pattern You can display a test pattern (color bars), useful and convenient in adjusting the image quality of the display. 1 2 3 Press the [MENU] button to display the Main menu. Output" and select "14: Test Pattern Select" from the sub-menu. The test pattern (color bars) is output. Value Displayed (No output) 1 2 3 Press the [MENU] button to display the Main menu. System" and select "1: System Frame Rate" from the sub-menu. Set each parameter to "60-NTSC" or "50-PAL. " 60-NTSC: NTSC format 50-PAL: PAL format Off 75% Color Bar 100% Color Bar 35 Switching Video Selecting the Video Switching Mode The V-44SW features two different video switching modes, "Direct mode" and "Preset mode. " Each mode functions in switching video as follows. Switching Video in Direct Mode Immediately after the power is turned on, SD VIDEO Channel 1 is assigned as the final output. 1 Press one of the SD VIDEO buttons [1]­[4] or one of the HD/RGB buttons [1]­[4] to select the channel. The selected button lights up, and the final output video is switched. Lit Direct Mode The final output video is switched when channels are selected with the press of a single button. Final Output Video Preset Mode When a channel is selected, the video in the preview monitor switches. Pressing the [TAKE] button confirms selection of this as the output video, switching the final output video. Preview Final Output Video Selecting an HD/RGB channel to which no signals are input may result in delayed switching of the video. About the Indicators Whenever video is being input to a channel, its indicator lights up. You can determine the type of video signal being input by observing the color of the indicator. Indicator Lit (Red) Lit (Green) Lit (Green) SD VIDEO1­4 Composite signal S-video signal No signal input HD/RGB1­4 RGB signal Component signal No signal input Selecting the Video Switching Mode 1 2 3 Press the [MENU] button to display the Main menu. System" and select "7: Panel Operation Mode" from the sub-menu. Select "Direct Mode" or "Preset Mode. " Direct Mode:video is switched in Direct mode. Preset Mode:video is switched in Preset mode. About the Colors of Channel Select Buttons You can change the colors in which channel select buttons light. 1 2 3 Press the [MENU] button to display the Main menu. [. . . ] 38 Wipe pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Z Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 70 For EU Countries This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC. For the USA FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]