User manual EDIROL RG-100

[. . . ] Owner's Manual Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (p. 2), "USING THE UNIT SAFELY" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, The manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Copyright © 2004 ROLAND CORPORATION All rights reserved. [. . . ] 116). Change effects. When using stamp material Effect list Change effects. When using text material Effect list 3 Drag-and-drop the selected effect to the "FRONT" track on the timeline. fig. editor16. eps Time Front clip "FRONT" track Effect Material When you drag-and-drop the effect to the desired starting position, the starting point is indicated by a bar, and the front clip appears as an icon in the "FRONT" track on the timeline. The material is selected automatically, so you may follow the instructions that follow to make your own selection of materials. 59 Creating a movie 4 Select a desired material from the list. The effect and material are shown in the "FRONT" track on the timeline. Drag-anddrop the selected material to the material icon in the "FRONT" track, and the material appears in the icon. Detailed settings for the front clip You can perform more detailed settings like editing the length of the clip, setting the loop mode, configuring the effect style, etc. 1 Click to select the created front clip, and then click [INFO. . . ]. When the stamp material is selected fig. effect info02. eps You can also double-click on the clip to access the EFFECT INFORMATION window. Effect Length Effect Loop [RESET] Material Stop Play [CANCEL] [OK] Effect configuration area 2 Click on either ends of the "Effect Length" slide bar to change the length of the clip. Click on the right end to lengthen, click on the left end to shorten the clip. The length of the clip is indicated in seconds on the right side of the slide bar. 3 Turn on/off the Effect Loop. Click the icon next to "Effect Loop" to turn on the loop setting, and the clip loop plays within the entire time of the movie (p. When loop is off, the clip plays just once. 4 Configure the effect settings. You can zoom in/out the material, shift the position, adjust the angles, etc. By clicking in the EFFECT INFORMATION window, you can view the current state of effects, so you can do the adjusting while monitoring the change of effects. To stop playback, click . 60 Creating a movie 5 Click [OK]. To cancel this operation, click [CANCEL]; the window goes away without the settings being saved. At the ending point of the background clip, a red triangle is marked in the "FRONT" track. When loop is set to on, it shows , and the movie loop plays the clip during the , and the movie plays the clip You can also select a material to be used in the EFFECT INFORMATION window. Click the material icon in the window, and a list of material names appears. Then click to select a desired material. entire length of the movie. When set to off, it shows only once. Editing the front clip In the timeline area, you can edit the clips. For example, you can change the starting point of the clips, or line up several clips along the time track. If you have created background clips, you can adjust these clips to play in unison by matching their play time or playback timings. fig. editor13. eps [COPY] [PASTE] [ERASE] [UNDO] When you click , you can easily align the clips with the gridlines (one second intervals) on the time track. Moving clips You can drag-and-drop to move the clips to any position on the time track. You can check the time of the starting and ending point at the time indicator on the upper level of the timeline. When you click , you can select one clip and all the rest down the line. This is convenient when you wish to adjust the position of a multiple number of clips at once. Adding clips You can add a new clip to the "FRONT" track by dragging-and-dropping another effect from the effects list. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ­ Consult the dealer or an experienced radio/TV technician for help. [. . . ]