User manual DUAL XDVD8181

[. . . ] XDVD8181 INSTALLATION/OWNER'S MANUAL DVD Multimedia Receiver with 7" Touch Screen Display TOUCH Safety Note: The DVD video display of the in-dash unit will not operate while the vehicle is moving. In-dash DVD video functions will only operate when vehicle is in Park and the parking brake is engaged. It is illegal in most states for the driver to view video while the vehicle is in motion. XDVD8181 PREPARATION Table of Contents Page DVD Region Management . 51 DVD Region Management Some DVD discs can be played only in certain playback modes according to the intentions of the software. [. . . ] Turn VOLUME rotary to desired listening level, press and hold VOLUME rotary knob for 3 seconds to program currently selected volume level. 17 DISP OPEN EJECT ROTARY MODE TRACK UP TRACK DOWN STOP PLAY/PAUSE FAST FORWARD FAST REVERSE MUTE POWER ON/OFF VOLUME PROGRAMMABLE TURN-ON VOLUME XDVD8181 OPERATION General Operation Secondary LCD Information 1 2 3 4 5 NOTE: Sub-LCD only functions when TFT monitor is closed. 1) LOC 2) ST 3) TIME 4) LOUD LOCAL indicator, icon will be off when DISTANT (DX) is selected STEREO radio station indicator Displays TRACK time, TUNING frequency, MP3 ID3 info, & CLOCK, etc LOUDNESS selection indicator 18 XDVD8181 OPERATION General Operation Main Menu Access There are three methods to access the MAIN menu · Press the ENTER button on the right ROTARY knob · Press the MENU button on the IR Remote control · Touch the A area (upper left hand side) on the touch screen 1 2 3 4 10 9 8 7 L 6 5 Touch Access Buttons 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) Rapid Dial Touch to access AM/FM TUNER mode Touch to access CD/DVD mode, CD/DVD must be inserted Touch to access AUXILIARY A/V INPUT mode Touch to RETURN to previous screen Touch to access CAMERA mode, if optional camera isn't connected then "No Video Signal" will be displayed Touch to STANDBY screen, touch screen again or any button to resume display. NOTE: VOLUME level can be controlled without interrupting STANDBY Touch to access SCREEN SETUP utility menu Touch to access GENERAL SETUP utility menu Touch to access CD/DVD SETUP menu, CD/DVD must be inserted to function Touch to access MAIN Source menu RAPID DIAL can also control touch screen functions · · · Select desired function rotating clockwise or counter-clockwise Function will be outlined in yellow Press inward to ENTER 19 XDVD8181 OPERATION System GENERAL Setup Menu General Setup Menu L · · · NOTE: Default anti-theft password is 0000 Press the GENERAL button to access the setup mode Select desired parameter you wish to change Page will return back to previous screen after 10 secs of inactivity or by pressing the RETURN button This is matrix of the GENERAL Setup Menu Settings Default Radio Clock adjust Clock Mode Camera Image USA AM 1Hr Normal Video Format Auto TFT Auto Open Antitheft code Antitheft Active Off 0000 Off Options USA S-AMER1 S-AMER Europe 00:00 1Hr 4Hr Normal Reverse AUTO NTSC PAL On Off Manual ---On Function Set to appropriate setting for your Country See adjusting the clock for more details PM 6:00 18:00 Normal Image Mirror camera input image 180 degrees System will auto detect NTSC or PAL For NTSC compatibility For PAL compatibility TFT panel will automatically open when IGN is turned on TFT willl remain closed until the OPEN button is pressed Will only close when OPEN Must enter password to turn antitheft on or off System will require a password if main battery power is removed for more than 5 minutes No Password will be required if power is removed Load all factory parameters to their original settlings, NOTE: this will not change ANTI-THEFT password Off Load Factory Yes Are you Defaults sure?Yes / Cancel NOTE: Not all GENERAL setup features are described in detail 0 XDVD8181 OPERATION System GENERAL Setup- Adjusting RADIO Frequency Adjusting RADIO Frequency L 1 1) Touch top left corner of screen Step 1 Step 2 L 2 ) Touch GENERAL setup button L 3 Step 3 3) Touch USA L L 5 4 Step 4 4) Touch the setting for your Country Step 5 Touch RETURN to exit 1 XDVD8181 OPERATION System GENERAL Setup- Adjusting the Clock 12Hr Clock Mode L 1 1) Touch top left corner of screen Step 1 Step 2 ) Touch GENERAL setup button L 2 Step 3 L 3 3) Touch 00:00 area in the CLOCK row L 7 Step 4, 5 , 6, 7 & 8 4) Keypad should now appear 5) Enter the time in HOURS, touch Ok 6) Enter MINUTES, touch Ok 7) Touch AM or PM to set 8) Touch RETURN to exit 24Hr Clock Mode LLL 8 5 6 If you desire 4Hr format, select 4Hr from CLOCK MODE, then follow steps 1-8 XDVD8181 OPERATION System GENERAL Setup- Setting the Anti-theft code By default Anti-theft password is 0000 and is turned OFF, to turn this feature on, follow the steps below. This will lock your unit from operating if battery POWER is disconnected for more than 5 minutes Step 1 & 2 L 1 1) Touch top left corner of screen ) Touch GENERAL Setup button L 2 L 4 Step 3 & 4 3) Touch down arrow button 3 L 4) Touch ---- NOTE: it is recommended Step 5 & 6 that you choose your own 4-digit password carefully, write it down somewhere and keep in a safe location. In the event you should ever loose or forget your password, call our tech hot line for support on how to unlock Step 7 & 8 your system 5) Enter 0000 L 5 7 L 6 6) Touch OFF 7) Touch ON L 10 9 L 8 8) Touch ---- again Record your password here Step 9 & 10 L L 9) Enter your new 4-digit password 10) Touch RETURN to exit 3 XDVD8181 OPERATION System SCREEN Setup Menu Screen Setup Menu · · · Press the SCREEN Setup button to access the SCREEN SETUP mode Select desired parameter you wish to change Page will return back to previous screen after 10 secs of inactivity or by pressing the RETURN button L Adjusting a Feature Settings Brightness Screen Tilt Screen Saver Touch Screen Calibration Version Default 10 4 On No Options 0 to +0 1-6 On Off No Yes Function Press the < / > buttons on the remote or rotate the ENTER button clockwise / count-clockwise to adjust the BRIGHTNESS to the desired setting Select 1 to 6 to adjust the default tilt angle of the screen Select On to activate the screen saver, Off to deactivate Touch "Yes" to enter the Touch Screen calibration mode Software version of unit System Standby To conserve the LCD backlight lifespan or to stop annoying glare while night driving, press STANDBY, the TFT screen only will black out, however all other operations are still possible, press any button except VOLUME or touch screen again to return normal viewing 4 L XDVD8181 OPERATION System SCREEN Setup Menu- Setting TFT Brightness This will set the default setting for the TFT display brightness, this setting can also be set by pressing the INFO button on the front TFT panel L 1 1) Touch top left corner of screen Step 1 Step 2 ) Touch SCREEN setup button L 2 L 3 Step 3 3) Touch [-] to DIM TFT L L 5 4 Step 4 4) Touch [+] to BRIGHTEN TFT 0 to + 0 is possible Default = 10 5) Touch RETURN to exit 5 Step 5 XDVD8181 OPERATION System SCREEN Setup- Setting TFT Angle Set for best viewing angle in your vehicle L 1 1) Touch top left corner of screen Step 1 Step 2 ) Touch SCREEN setup button L 2 L 3 Step 3 3) Touch a number displayed in SCREEN TILT row Step 4 L L 5 4 4) Touch desired angle for best viewing angle 1 -6 is possible Default = 4 5) Touch RETURN to exit Step 5 6 XDVD8181 OPERATION System SCREEN Setup - Touch Screen Calibration On occasion the touch screen will have to be calibrated, follow these few steps as described L 1 1) Touch top left corner of screen Step 1 Step 2 ) Touch SCREEN setup button L 2 Step 3 & 4 L LL 7 3 4 3) Touch NO in TS Calibration row 4) Then press YES Note: For proper calibration you must touch each pointer for 2 seconds. If pointers are not touched properly, the calibration sequence will start over until the calibration is done correctly. Step 5 & 6 5) Touch and hold the pointers as indicated on the screen for seconds each. 6) Screen will automatically return to MAIN MENU, touch EXIT to return. 7 XDVD8181 OPERATION AM/FM Tuner Operation AM/FM Tuner TFT Display 1 19 18 2 3 4 5 6 17 16 L 15 14 13 12 11 10 9 8 7 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) 16) 17) 18) 19) 8 Current source MODE information, touch "A" area to return to MAIN source selection menu Current PRESET station indicator STEREO broadcast indicator Clock PRESET page up LOCAL / DISTANCE selection PRESET page down Auto station SCAN button MANUAL TUNE up MANUAL TUNE down SEEK TUNE up SEEK TUNE down AS/PS (AUTO STORE / PRESET SCAN) BAND selection, FM1, FM, FM3, AM -> FM1 VOLUME indicator LOUD indicator Equalizer indicator, touch to access AUDIO Setup menu Current radio frequency indicator Current radio BAND indicator XDVD8181 OPERATION AM/ FM Tuner Operation Auto Seek Tuning Press the Press the Manual Tuning Press the Press the Auto Store (AS) button to auto SEEK up the next strongest station. button to manually tune down one step at a time. Press and hold AS/PS for more than seconds to automatically store the twelve strongest stations in the current band. Automatic Local tuning is activated during the initial band scan, repeat for other bands. NOTE: All presets within the current band will be overwritten. Program Scan (PS) SCAN Press AS/PS for less than seconds to scan presets 1-1 on the current band, pausing for 5 seconds at each. Press SCAN to preview strong stations on the current band, pausing for 5 seconds at each station. Touch LOC button on the TFT to activate LOC / DX When the LOCAL function is on, LOC will appear, only radio stations with a strong signal are received, DX is for radio stations that are far away and/or have weak signals. Press and hold the desired preset button (1-1) for more than seconds. The station can be recalled anytime by pressing the corresponding preset button on the TFT. Only 6 PRESETS can be display at one time, use PRESET page up/down to access next stored PRESETS accordingly. LOC/DX Radio Station Storing Radio Stations PRESET Recalling a Radio Station PRESET PRESET Page Up/Down L 9 XDVD8181 OPERATION DVD Operation DVD Region Management Some DVD discs can be played only in certain playback modes according to the intentions of the software. As the XDVD8181 plays discs according to their intentions, some functions may not work as intended. This player has been designed to play back DVD software that has been encoded for specific region areas. It cannot play back DVD software encoded for other region areas than the region areas for which it has been designed. The XDVD8181 will play discs labeled "Region 1" or "All". DVD region codes: 1 - USA, Canada - Japan, Europe, South Africa, Middle East 3 - Rep. [. . . ] MP3/WMA written in the formats other than the above may not play and/or their file names or folder names may not be displayed properly. 47 Compatible Recording Formats XDVD8181 OPERATION Troubleshooting Problem Unit will not turn on (no power) Cause Black wire not connected Fuse blown Action Check connection to ground Replace fuse Check connections at speakers Insulate all bare speaker wires from each other and chassis ground Check for pinched wire Check for pinched wire Use fuse with correct rating Check connections at parking brake Apply parking brake Check connections at reverse lamp Select reverse gear Set rear view to ON - see page 14 for details Check media for scratches Use discs labeled "Region 1" or "All" only. Replace battery Check mounting sleeve Check media for scratches Press eject or RESET Use only DVDs labeled "Region 1" or "All" only. Remove the obstacle and press OPEN again to resume the monitor open/close sequence. Yellow wire not connected or incorrect voltage Check connections for proper voltage (11~16VDC) Red wire not connected or incorrect voltage Unit has power (but no sound) Unit blows fuse Speaker wires not connected One or more speaker wires touching each other or touching chassis ground Yellow or red wire touching chassis ground Speaker wires touching chassis ground Incorrect fuse rating Unit has audio (but no video) No video display (when in reverse) Parking brake safety circuit not connected Parking brake not applied Reverse circuit not connected Vehicle is not in reverse Rear view set to OFF DVD does not start playback Physical defect in media Wrong region IR remote does not work Excessive skipping ERR-DISC appears on display Region code error appears on display Front panel will not open/close Dead battery Unit is not mounted correctly Physical defect in media Focus error or disc is in upside down Region code error Front panel obstructed 48 XDVD8181 OPERATION Limited One Year Warranty This warranty gives you specific legal rights. [. . . ]