User manual DEI ORION P5.2

[. . . ] As we are always finding new ways to improve our product, the features and specifications are subject to change without notice. PRACTICE SAFE SOUNDTM Continuous exposure to sound pressure levels over 100dB may cause permanent hearing loss. High powered automotive sound systems can generate sound pressure levels in excess of 130dB. When playing your system at high levels, please use hearing protection and prevent long term exposure. [. . . ] Many shade tree installers overlook this and check for clearance only when the door is fully open. 2 REAR DECK MOUNTING In rear deck installations, check the operation of the trunk suspension springs or tension bars. You cannot be too cautious during this part of the installation, In addition, do not locate the speakers too close to the back of the rear deck. Installing the far screws will only be possible with the removal of the rear window. INSTALLING THE MIDRANGE Step 1: Determine where the speaker will be mounted. Make sure there is a flat area large enough for the speaker to fit properly. Step 2: Check to make sure the space you have chosen for the speaker will not interfere with the operation of the vehicle. When using correctly sized factory locations, this step can be passed. A hole can be cut either with a pair of metal tin snips, an air or jig saw, or with a hole saw corresponding to the size of the midrange listed below. · 4-11/16" Hole Saw (5" woofer installation) · 5-5/8" Hole Saw (6" woofer installation) WARNING: Window mechanisms and electrical wires have a nasty habit of hiding where you least expect. Step 6: Using the plastic grille ring as a template, mark the mounting holes with a pen. WARNING: Window mechanisms and electrical wires have a nasty habit of hiding where you least expect. Step 8: Pull the wire through the speaker opening and connect to the speaker. Be sure to observe proper midrange polarity during this process. 3 Step 9: Mount the speaker- The speaker is placed in the grille ring from the front. INSTALLING THE TWEETER SURFACE MOUNTING Step 1: Determine the tweeter mounting location, then route the wires from the crossover to the tweeter location. Step 2: Place the surface mount housing against the panel and mark the two holes at the rear of the housing. Step 4: Drill the larger off-center hole using a 3/8" drill bit, insert a grommet and route the speaker wire from the crossover through the grommet. Step 5: After removing the surface mount tweeter assembly trim ring, route the tweeter wires through the larger hole in the housing and connect to the speaker wires from the crossover. (See Figure 4. ) Step 6: Insert the excess speaker wire into the hole and position the housing so the housing will not pinch the wires after final mounting. Step 7: Attach the housing using the supplied screws of the correct length for a solid mount. Step 8: Insert the tweeter into the housing and attach the trim ring. 4 FLUSH MOUNTING INTO REMOVED PANELS (diagram A) Step 1:. Determine the tweeter mounting location, then route the wires from the crossover to the tweeter location. Step 3: If using a hole saw, first drill a pilot hole, then cut out the hole using a standard 2-1/8" hole saw. [. . . ] Changing the polarity of the tweeter may be necessary for optimum sound quality. + - TWEETER + - TO AMPLIFIER WOOFER + - SPECIFICATIONS Model Nominal Impedance Power Continuous/Peak Frequency Response Sensitivity Mounting Depth Mounting Diameter Orion P5. 2 4 ohms Orion P6. 2 4 ohms 100/150 70Hz - 22kHz 87 dB w/grille 2. 75" w/o grille 2. 5" 100/150 60Hz - 22kHz 89 dB w/grille 3" w/o grille 2. 75" 411/16" 6 55/8" Warranty LIMITED TWO YEAR CONSUMER WARRANTY: Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be defective in workmanship or material under normal use, for a period of two years from the date of purchase from the dealer as indicated by the date code marking of the product PROVIDED the product was installed by an authorized Directed dealer. During this two-year period, there will be no charge for this replacement PROVIDED the unit is returned to Directed, shipping pre-paid. [. . . ]