User manual DEI OHD901 Owners Guide

[. . . ] OWNER'S GUIDE INSTALLATION GUIDE 9" (16:9) Overhead Video Monitor/DVD Player MODEL OHD901 © 2005 Directed Electronics, Inc. N82901 03-05 NON-TRANSFERABLE LIMITED ONE YEAR CONSUMER WARRANTY Directed Electronics, Inc. (Directed) promises to the original purchaser that the new automotive video monitor and/or source unit(s) (the Product) that is purchased and installed from a Directed authorized dealer more than ninety (90) days after the purchase of a new vehicle are warranted for a period of one (1) year from date of purchase of the Product. Directed promises to the original purchaser that all video accessories will be free from defects in materials and workmanship under normal use and condition for a period of ninety (90) days after the date of purchase. [. . . ] On the remote use the up/down cursor buttons located at either side of the menu button. On the monitor use the cursor buttons to the right side of the button. If a button is not activated within 5 seconds, this function mode will turn OFF. Once the correct function is selected, press the cursor button (to set the desired setting). If no button is pressed, the menu mode will turn OFF in about 5 seconds. The FM frequency setting allows the monitor to transmit audio to the vehicle's radio. Use a frequency that is not interfered with from a local broadcast station. This setting also has an OFF position. © 2005 Directed Electronics, Inc. 21 DOOR LIGHT ON/OFF Engage this switch on the monitor to activate the dome lights when a door is open. NOTE: This function is operational only when the Gray wire of the dome light circuit is connected to the door switch. COURTESY LIGHT ON/OFF Activate this switch on the monitor to control the dome light illumination. 22 © 2005 Directed Electronics, Inc. Basic Functions DVD PLAYBACK 1. Press the remote control's POWER button or the monitor's POWER button to switch on the unit's power. Select video source (DVD). NOTE: If there is no disc in the DVD player, a "NO DISC" message will be displayed N in the upper left corner of the screen. 3. Load a disc into the unit. The message "READ" will appear in the upper left corner of the screen. DVD playback commences. NOTE: The disc will start to play if there are no titles recorded on the disc. If one or more titles are recorded on the disc, a menu will appear on the LCD screen. 5. Press / / / on the remote (or their equivalent on the DVD player) to select the preferred item or title from the menu. Press the ENTER (on remote or DVD player) button, the selected item will now start playing. After viewing completion, press the POWER button to put the unit into standby mode. NOTE: If the "WRONG REGION" message appears, it means that the corresponding operation is prohibited either by the player or by the disc. FAST FORWARD OR REVERSE (DVD/MP3/CD) F 1. Each time this button is pressed, the unit will go into a rapid advance playback mode. This will be shown on the LCD, depending on the speed of the playback selected. playback FF 2X FF 4X FF 8X FF 20X PLAY P Press "PLAY" button, the speed will go back to standard. © 2005 Directed Electronics, Inc. 23 F 2. Each time this button is pressed, the unit will go into a rapid reverse playback mode. This will be shown on the LCD, depending on the speed of the playback selected. playback FR 2X FR 4X FR 8X FR 20X PLAY P Press "PLAY" button, the speed will go back to standard. Press the "NEXT" MP3/Audio CD button during playback. The player will skip forward to the next track each time the button is pressed. DVD The player will skip forward to the next title/chapter each time the button is pressed. Press the "PREV" MP3/Audio CD button during playback. The player will skip to the beginning of the previous track each time the button is pressed. [. . . ] DOUBLE CHECK THE LENGTH OF THE SCREWS PRIOR TO MOUNTING THE BRACKET, TO PRECLUDE PENETRATION OF THE VEHICLE'S ROOF. 36 © 2005 Directed Electronics, Inc. Roof Beam Support Optional Spacer Material (Installer Provided) Metal Bracket Screws (not included) Screws (Included) 6. Cut a 1" hole in the headliner along the backside of the mounting bracket for the cables to pass through. Route cables through the hole to the predetermined location of the AV source(s). Identify the dome light wires in the vehicle and connect them to the corresponding dome light wires on the overhead monitor system. Plug in the AV, DIN and power cables into the overhead monitor system. 10. [. . . ]